MSefi.com read only forum (Jan.15,2018)

Thanks a lot Matt for the info.
I will load my new msq file with no hassle.

Hi,
I'm using MS2 V3 . I already calibrated my sensors in megatune and it runs fine.
I have a new edited msq file in my other laptop , If I load it to my ecu, do I need to calibrate again my sensors in megatune?

thanks,

I will post my datalog files later, i'll have to get an new bosch o2 sensor cause mine is broken

Hi,
I'm using MS2 v3 with edis4 ignition on my 4age 16v engine.
I fairly tune my engine using LC-1 with the help of megalog viewer.
I find the stable idling at 13.3 afr

My problem now is when idle at 800rpm then suddenly press the accelerator and release the pedal, my rpm dips to 500rpm and then ...

Hi,
I found the problem why there is no trigger output on my MS2 .I found that here is no +12v supply on IC U4 (IXDI404PI).
I see burnt traces in front of C14 ,this traces is connected after D3 . I found out that the C14 (4.7uf) capacitor is shorted.
I replace it and now my MS2 is working great and ...

Hi,
I reloaded the code again and I'm having a problem on the end of the the process. In the manual it said that it should dispaly
"Verification succeeded, 999 records total (4 skipped)." but mine is diffirent and here it is

MegaSquirt Download 2.00

Reading C:/Documents and Settings/Remy ...

Hi,
I tested my ms2 today and still finding what is the cause of no injector trigger output.
I have no oscilloscope so I used test LED to do this. I dont see any trigger pulse on the Gate of the Injector mosfet while cranking.

I updated and load new code (v2.890.abs.s19) to the MS2 chip .
The ...

Hi Matt,
I have no stimulator right now,but I have confirm that there is no trigger in the injector.I make an LED with resistor on anode then put in the injector socket. Cathode of LED connected to MS injector output then the anode of LED to the +12v supply. Then I try to start the engine and no ...

Hi Matt,
Here is my msq and datalog while cranking.

thanks,

Hi Matt,
Yes, I see RPM when i crank the engine.

Hi ,
I'm using MS2 V3 in toyota engine and the engine run fine.
Lately , Im tuning the Warmup wizard in megatune
I have slowly decrease the value from 100 down to 65 then suddenly
my engine stop. I try to crank it few time but still not starting.
The communication of megatune to MS2 is fine.
I ...

More advance, no EGO correction at idle, and tuning the ve and spark table right.

How much are we talking?


Thanks, I already turn off the EGO correction at idle .
Right now , 15deg is set on my spark advance table at idle andI have'nt try to tune the spark table at idle .
I will try to play ...

hi,
Im using MS2 V3 with EDIS4 on toyota 4age 16v engine.The Engine runs great and I'm have partially street tuned the engine with innovate LC-1 and im very happy for result of the engine response in using MS2.

The engine idling are set 800 rpm with 14.7:1 AFR. , the rpm bouncing (up and down ) a ...

thanks .. my 4age engine harness has an existing capacitors.. i will used it.

Hi all,
What is the effect if I don't install the 24uf capacitor on stock EDIS coil pack?

the article suggested to used TIP120 because its a lot cheaper than the VB921 for switching the igniter.

i'm planning to use TIP41c instead of the TIP120 because i have a spare of this transistor at home,

i checked their data sheet and
notice that the TIP41C is "NPN epitaxial silicon transistor ...

im also using MS2 v3 in my 4age toyota engine.

can i directly connect the OEM knock sensor to MS2 (PIN JS4)?

can it damage my CPU,? i think that the oem knock sensor produces low voltage.

thanks for the links

ivanlau78 wrote:

katok wrote:
thanks for that information lance.

i'm about to set-up my MS2 to a 4age using JDM igniter.

any update on your 4age MS2 setup? can you let me know your 4age is 16v or 20v?

my engine is 16v engine (tvis)
i will start my project in a few weeks from now

Lance wrote:katok,

As far as I am aware, the toyota igniter used with the VAST system does not control the dwell, it relies on the ECU to do this.

Lance.

thanks for that information lance.

i'm about to set-up my MS2 to a 4age using JDM igniter.