MSefi.com read only forum (Jan.15,2018)

Thanks, all fixed

I use registered TS on an old notebook running linux. I hadn't used it for awhile and hooked to the MS and it asked if I wanted to update. I said no. Hooked onto car and everything worked as expected. After I finished my session and was in house I started TS again. When it asked if I wanted to ...

Thank you . All working now.

I have a registered shadow dash, I have it connected to my android tablet via bluetooth and it all works. I did a drive and logged two sessions. I can find the files on the tablet but it says it can't find a program to read it. Am I doing something wrong or do I need another program like shadow ...

Thanks, I think I getting now.

I will separate them but I expect it is my limited understanding of grounds. When the grounds get to the MS pins 7 through 19 are all common and that is the part that has me not understanding why they should be separated. I am not questioning I am just trying to understand.

I am doing a ms2 b&g 2.92 fuel only. In early documentation the tps ground just went to ground. Later documentation has tps ground to pin 19 to help with noise. In my case the tps is shared with the factory gm pcm which all the gm grounds ground to a stud on the intake. Rather than physically solder ...

Thanks, old school terminology and old eyes. Not a good combo. Merry Christmas to you and thanks for always helping out with problems.

I let my TS do an update and then decided to do some rearranging on my gauges. I no longer can find a gauge RPM, only rpm dot, is that the same thing?

Thanks..I live on an island so couldn't get one till I go off but now went to an old junk bucket and fount an old 10 footer so tried an all is well. Will get shorter when I go off.

I have your Bluetooth adapter and using it with ms2 3.57. The area right behind the mounting screws is very hard to get at and the ms2 is in an awkward spot. So I thought maybe a 1' straight through cable could be installed and just be left as a pigtail for when it is needed. Does there appear to be ...

All is working now. Although I triple checked the reg code I didn't check that I was entering my TS reg. sorry to take up your time.

Hi
I have a shadow dash registration and have used it on a Linux notebook and a smart phone. I haven't used it for about 6 month and just got a new samsung tablet. It started up fine and gave me the 3 minute demo and all seemed ok. Then it asked for the info that came in the reg email and entered ...

I have a recent MS 3.57 from DIYAutoTune. I can use either b&g or extra. I currently have a bbc running a msd billet low profile dist connected to an external gm 4 pin module. I have been running fuel only on 2 other cars for years with high success but haven't had good success with ignition. So ...

The little netbook I use for tuning is on Ubuntu and it doesn't have a print screen feature. Is there a way to print tables. I go between several different controller/vehicles and would like to have a hard copy when comparing. Also on same netbook I have VE table 1 gone to full screen and I don't ...

I have read everything I could but wasn't sure so the question. With MS2 V3 code 2.92, if you select dual table and you have the same VE and AFR in both tables 1 and 2, would bank 1 or inj1 on relay board be controlled by VE table 1 and bank 2 or inj2 on relay board be controlled by VE table 2 ...

no it doesn't work straight up. I suppose an electronics guy could make it work with stuff that is above my pay grade.

MS2 ver3 code 2.92. Has anyone used the hei8 ref square wave signal (tach) to control two separate ecu's at the same time.
I am running stock gm computer and megasquirt. The gm controls ignition via msd box, controls fuel pump, transmission and TC and injector 12V. Megasquirt controls injector ...

I am running embedded 2.92. I see now more how it works. My phone is an old smart phone and I don't have a data plan and where the car is there is no wifi. So that would be why I didn't get and auto update. Maybe a note about that in the install memo would be good for us not so computer savy guys ...

All working now. I had to manually import the ini, project and dash from my ubuntu TS notebook. SD wouldn't pick it up on it's own. Being as I am almost illiterate in linux speak it was real time consuming. Anyhow pretty awsome went it gets working.