Hello,
Having some problems with my Megasquirt II w/v3.57 SMD board running 2.88 code.
I have the Toyota 4E-FTE 1.3L 4 cylinder engine, with the 4E-FE distributor attached (as it has a inbuilt coil and ignitor inside, to simplify things) I am not getting any ignition signal to the MSII.
Can anyone point me in the right direction or provide info on how to wire up this distributor?
I can find the coil supply +12V wire, the tach ouput wire from ignitor, the wire connected to the F terminal on the ignitor, the wire connected to the T terminal on the ignitor, and the two wires that go to the 4-toothed wheel pickups (two pickups set 90 degrees apart and wired in series inside the distributor, providing two wires output). The negative side of the coil is connected to the ignitor ouput internally within the distributor.
Currently I have pin 36 from MSII wired to the T wire on the ignitor (what I beleive to be the ignitor trigger wire, the two wires from the 4-tooth wheel pickups to the vr input on the MSII and the +12V supply wired to the main relay +12V.
Anyone?
Kind Regards,
DanV
HELP PLEASE - Toyota 4E-FTE Starlet Distributor Wiring
Forum rules
Read the manual to see if your question is answered there before posting. Many users will not reply if the answer is already available in the manual.
If your question is about troubleshooting, configuration, or tuning, you MUST include your processor type (MS-I or MS-II) and code version in your post. If your question is about PCB assembly or modifications, you must also include the main board version number (1.01, 2.2 or 3.0). For tuning/troubleshooting questions, please attached a datalog and your MSQ file to your post.
If you have questions about MS1/Extra or MS2/Extra code configuration or tuning, please post them at www.msextra.com Such questions posted here will be moved to: a temporary MSextra sub-forum, where they will be removed after 7 days
The full forum rules are here: Forum Rules, be sure to read them all regularly.
Read the manual to see if your question is answered there before posting. Many users will not reply if the answer is already available in the manual.
If your question is about troubleshooting, configuration, or tuning, you MUST include your processor type (MS-I or MS-II) and code version in your post. If your question is about PCB assembly or modifications, you must also include the main board version number (1.01, 2.2 or 3.0). For tuning/troubleshooting questions, please attached a datalog and your MSQ file to your post.
If you have questions about MS1/Extra or MS2/Extra code configuration or tuning, please post them at www.msextra.com Such questions posted here will be moved to: a temporary MSextra sub-forum, where they will be removed after 7 days
The full forum rules are here: Forum Rules, be sure to read them all regularly.
nevermind the above..........
I simply adjusted POT56 (the VRAdjust POT) and I am now getting an ignition signal to the MSII when cranking. (stupid me for not thinking of it the first time i know....)
I now have a flat battery though......
I will check to see if I have wired the Stock'o toyota ignitor inbuilt into the distributor tomorrow when I will have a charged battery.
DanV
I simply adjusted POT56 (the VRAdjust POT) and I am now getting an ignition signal to the MSII when cranking. (stupid me for not thinking of it the first time i know....)
I now have a flat battery though......
I will check to see if I have wired the Stock'o toyota ignitor inbuilt into the distributor tomorrow when I will have a charged battery.
DanV
Re: HELP PLEASE - Toyota 4E-FTE Starlet Distributor Wiring
i know this is a bit old but how did it end up?
im looking to use MS on my 4e-fte...
cheers,
Sheldon
im looking to use MS on my 4e-fte...
cheers,
Sheldon