EDIS Wire ends
EDIS Wire ends
Does anybody know where to get the wire ends to convert my plug wires to EDIS? Somebody other than Boost Engineering? He hasn't responded to any of my emails or returned any phone calls. Just looking for an alternative
66 VW squareback
MS2 V3.57
Late model factory Plenum
EDIS Ignition
1679cc Turbocharged!
MS2 V3.57
Late model factory Plenum
EDIS Ignition
1679cc Turbocharged!
-
kjones6039
- Master Squirter
- Posts: 618
- Joined: Sat Jul 22, 2006 7:02 pm
- Location: Eureka, Nevada USA
- Contact:
Re: EDIS Wire ends
Hmmmmm......
Those &^%(%^ ends are almost impossible to find except at Boost Engineering!
Actually I got very good service from Boost on all the business I have done with them. I hope nothing has changed there!
Ken
Those &^%(%^ ends are almost impossible to find except at Boost Engineering!
Actually I got very good service from Boost on all the business I have done with them. I hope nothing has changed there!
Ken
1979 Corvette - 383 CID SBC w/ Holley Pro-Jection 900 CFM TBI, 4-85 lb lo-z injectors & Walbro 255 pump
MS2 v3 w/ms2extra 3.4.0 Release
36-1, Delphi LS2/7 coils in wasted spark, driven by v2.0 logic board from JBPerformance
Spartan Lambda Sensor from 14point7
MS2 v3 w/ms2extra 3.4.0 Release
36-1, Delphi LS2/7 coils in wasted spark, driven by v2.0 logic board from JBPerformance
Spartan Lambda Sensor from 14point7
Re: EDIS Wire ends
Alternatives
Get hold of original EDIS HTleads from a scrapyard, and reuse the connectors onto your plugwires.
Or use the original EDIS HTleads and put on the appropriate spark plug boots.
W113
Get hold of original EDIS HTleads from a scrapyard, and reuse the connectors onto your plugwires.
Or use the original EDIS HTleads and put on the appropriate spark plug boots.
W113
If it is not understood , it will not work!
Re: EDIS Wire ends
Ya I thought of that option as well. 
66 VW squareback
MS2 V3.57
Late model factory Plenum
EDIS Ignition
1679cc Turbocharged!
MS2 V3.57
Late model factory Plenum
EDIS Ignition
1679cc Turbocharged!
-
Peter Florance
- Helpful Squirter
- Posts: 44
- Joined: Fri Apr 02, 2004 7:40 pm
- Location: Virginia Beach, VA
- Contact:
Re: EDIS Wire ends
We used a Ford coil on the Vtec Mini. I can't recall where Mike got the ends but I think someone at NAPA ordered them for him
He made the wires right on the car
If you are interested, I can check on the part #
He made the wires right on the car
If you are interested, I can check on the part #
Peter Florance
1981 BMW 528i
"Friends don't let friends use adjustable timing lights"
1981 BMW 528i
"Friends don't let friends use adjustable timing lights"
-
Peter Florance
- Helpful Squirter
- Posts: 44
- Joined: Fri Apr 02, 2004 7:40 pm
- Location: Virginia Beach, VA
- Contact:
Re: EDIS Wire ends
Peter Florance
1981 BMW 528i
"Friends don't let friends use adjustable timing lights"
1981 BMW 528i
"Friends don't let friends use adjustable timing lights"
-
kjones6039
- Master Squirter
- Posts: 618
- Joined: Sat Jul 22, 2006 7:02 pm
- Location: Eureka, Nevada USA
- Contact:
Re: EDIS Wire ends
I am a little concerned with the picture in that link. The ends don't look right to me.
I had a TERRIBLE time finding these connectors for my setup. About $50 dollars when I finally got them!
Ken
The above description says HEI which definitely will not work with the Ford EDIS coil packs......Incl. Socket And HEI Spark Plug Top Distributor Caps - Multi-Angle Boots / Terminals;
I had a TERRIBLE time finding these connectors for my setup. About $50 dollars when I finally got them!
Ken
1979 Corvette - 383 CID SBC w/ Holley Pro-Jection 900 CFM TBI, 4-85 lb lo-z injectors & Walbro 255 pump
MS2 v3 w/ms2extra 3.4.0 Release
36-1, Delphi LS2/7 coils in wasted spark, driven by v2.0 logic board from JBPerformance
Spartan Lambda Sensor from 14point7
MS2 v3 w/ms2extra 3.4.0 Release
36-1, Delphi LS2/7 coils in wasted spark, driven by v2.0 logic board from JBPerformance
Spartan Lambda Sensor from 14point7
-
Peter Florance
- Helpful Squirter
- Posts: 44
- Joined: Fri Apr 02, 2004 7:40 pm
- Location: Virginia Beach, VA
- Contact:
Re: EDIS Wire ends
I'll check with the local shop. That was my experience too and was surprised when they were delivered the next daykjones6039 wrote:I am a little concerned with the picture in that link. The ends don't look right to me.
The above description says HEI which definitely will not work with the Ford EDIS coil packs......Incl. Socket And HEI Spark Plug Top Distributor Caps - Multi-Angle Boots / Terminals;
I had a TERRIBLE time finding these connectors for my setup. About $50 dollars when I finally got them!
Ken
Peter Florance
1981 BMW 528i
"Friends don't let friends use adjustable timing lights"
1981 BMW 528i
"Friends don't let friends use adjustable timing lights"
Re: EDIS Wire ends
Peter Florance wrote:We used a Ford coil on the Vtec Mini. I can't recall where Mike got the ends but I think someone at NAPA ordered them for him
He made the wires right on the car
If you are interested, I can check on the part #
Could you please? I ended up buying an aftermarket set of wires from autozone for a 92 escort 1.9 and they worked for my application. The lengths were just right. I would really appreciate those numbers for future reference.
66 VW squareback
MS2 V3.57
Late model factory Plenum
EDIS Ignition
1679cc Turbocharged!
MS2 V3.57
Late model factory Plenum
EDIS Ignition
1679cc Turbocharged!