edis wheel balance
Forum rules
Read the manual to see if your question is answered there before posting. Many users will not reply if the answer is already available in the manual.
If your question is about troubleshooting, configuration, or tuning, you MUST include your processor type (MS-I or MS-II) and code version in your post. If your question is about PCB assembly or modifications, you must also include the main board version number (1.01, 2.2 or 3.0).
If you have questions about MS1/Extra or MS2/Extra code configuration or tuning, please post them at www.msextra.com Such questions posted here will be moved to: a temporary MSextra sub-forum, where they will be removed after 7 days
The full forum rules are here: Forum Rules, be sure to read them all regularly.
Read the manual to see if your question is answered there before posting. Many users will not reply if the answer is already available in the manual.
If your question is about troubleshooting, configuration, or tuning, you MUST include your processor type (MS-I or MS-II) and code version in your post. If your question is about PCB assembly or modifications, you must also include the main board version number (1.01, 2.2 or 3.0).
If you have questions about MS1/Extra or MS2/Extra code configuration or tuning, please post them at www.msextra.com Such questions posted here will be moved to: a temporary MSextra sub-forum, where they will be removed after 7 days
The full forum rules are here: Forum Rules, be sure to read them all regularly.
edis wheel balance
my crank wheels seems to wobble a bit, it's definite noticeable , could this be throwing my idle off, , how perfect does the wheel need to be, because i had a shop weld it on., .
1986 toyota cressida
5m-gte 2.8 L6
MS-2 3.57 edis 6,
5m-gte 2.8 L6
MS-2 3.57 edis 6,
-
kjones6039
- Master Squirter
- Posts: 618
- Joined: Sat Jul 22, 2006 7:02 pm
- Location: Eureka, Nevada USA
- Contact:
Re: edis wheel balance
In my experience, a little wheel wobble is par for the course after welding. I found mine easy enough to correct by tapping it with a hammer as I rotated it, using the sensor as the indicator.
As for your question, I doubt that a small amount of wobble would cause too much problem with your idle.
Perhaps the experts will disagree with me though. We'll see......
Ken
EDIT: How much run out are we talking here?
As for your question, I doubt that a small amount of wobble would cause too much problem with your idle.
Perhaps the experts will disagree with me though. We'll see......
Ken
EDIT: How much run out are we talking here?
1979 Corvette - 383 CID SBC w/ Holley Pro-Jection 900 CFM TBI, 4-85 lb lo-z injectors & Walbro 255 pump
MS2 v3 w/ms2extra 3.4.0 Release
36-1, Delphi LS2/7 coils in wasted spark, driven by v2.0 logic board from JBPerformance
Spartan Lambda Sensor from 14point7
MS2 v3 w/ms2extra 3.4.0 Release
36-1, Delphi LS2/7 coils in wasted spark, driven by v2.0 logic board from JBPerformance
Spartan Lambda Sensor from 14point7
-
kjones6039
- Master Squirter
- Posts: 618
- Joined: Sat Jul 22, 2006 7:02 pm
- Location: Eureka, Nevada USA
- Contact:
Re: edis wheel balance
That's pretty small alright........
About .040". I doubt it has anything to do with your idle problem.
I should have asked before but, what is the clearance between your vr sensor and wheel?
Ken
About .040". I doubt it has anything to do with your idle problem.
I should have asked before but, what is the clearance between your vr sensor and wheel?
Ken
1979 Corvette - 383 CID SBC w/ Holley Pro-Jection 900 CFM TBI, 4-85 lb lo-z injectors & Walbro 255 pump
MS2 v3 w/ms2extra 3.4.0 Release
36-1, Delphi LS2/7 coils in wasted spark, driven by v2.0 logic board from JBPerformance
Spartan Lambda Sensor from 14point7
MS2 v3 w/ms2extra 3.4.0 Release
36-1, Delphi LS2/7 coils in wasted spark, driven by v2.0 logic board from JBPerformance
Spartan Lambda Sensor from 14point7
Re: edis wheel balance
i'll get video and measure.,
1986 toyota cressida
5m-gte 2.8 L6
MS-2 3.57 edis 6,
5m-gte 2.8 L6
MS-2 3.57 edis 6,