do i need the relay, or could i just run it straight to my tps??
i have toyota cressda with 5m-ge
do i need relay for gm 7-pin hei ???
Forum rules
Read the manual to see if your question is answered there before posting. Many users will not reply if the answer is already available in the manual.
If your question is about troubleshooting, configuration, or tuning, you MUST include your processor type (MS-I or MS-II) and code version in your post. If your question is about PCB assembly or modifications, you must also include the main board version number (1.01, 2.2 or 3.0). For tuning/troubleshooting questions, please attached a datalog and your MSQ file to your post.
If you have questions about MS1/Extra or MS2/Extra code configuration or tuning, please post them at www.msextra.com Such questions posted here will be moved to: a temporary MSextra sub-forum, where they will be removed after 7 days
The full forum rules are here: Forum Rules, be sure to read them all regularly.
Read the manual to see if your question is answered there before posting. Many users will not reply if the answer is already available in the manual.
If your question is about troubleshooting, configuration, or tuning, you MUST include your processor type (MS-I or MS-II) and code version in your post. If your question is about PCB assembly or modifications, you must also include the main board version number (1.01, 2.2 or 3.0). For tuning/troubleshooting questions, please attached a datalog and your MSQ file to your post.
If you have questions about MS1/Extra or MS2/Extra code configuration or tuning, please post them at www.msextra.com Such questions posted here will be moved to: a temporary MSextra sub-forum, where they will be removed after 7 days
The full forum rules are here: Forum Rules, be sure to read them all regularly.
do i need relay for gm 7-pin hei ???
do i need the relay, or could i just run it straight to my tps??
i have toyota cressda with 5m-ge
1986 toyota cressida
5m-gte 2.8 L6
MS-2 3.57 edis 6,
5m-gte 2.8 L6
MS-2 3.57 edis 6,
-
Matt Cramer
- Super Squirter
- Posts: 2951
- Joined: Sat Jul 03, 2004 11:35 am
Re: do i need relay for gm 7-pin hei ???
It appears to depend on the module - some let you get away with it and some don't.
Re: do i need relay for gm 7-pin hei ???
also, where do you put the Ground Shield when you run the GM 7pin module?
1986 toyota cressida
5m-gte 2.8 L6
MS-2 3.57 edis 6,
5m-gte 2.8 L6
MS-2 3.57 edis 6,
-
Matt Cramer
- Super Squirter
- Posts: 2951
- Joined: Sat Jul 03, 2004 11:35 am
Re: do i need relay for gm 7-pin hei ???
Grounded at the MS end only.
Re: do i need relay for gm 7-pin hei ???
ok, i have it all hooked up. but signal is working but on/off, i have a drill hooked up to my distributor, when it is reading, i can rev the drill and the rpm is consistant, but once i stop spinning, then i have to spin the drill twice to get it reading again,
or if i even spin the drill backwards it starts working right away.
or if i even spin the drill backwards it starts working right away.
1986 toyota cressida
5m-gte 2.8 L6
MS-2 3.57 edis 6,
5m-gte 2.8 L6
MS-2 3.57 edis 6,