Hello,
I installed an LC-1 wideband O2 on my MS II. I changed from narrow band to LC-1 wideband in the configurator file, and the virtual dash displays correct voltage range for wideband. I have set the EGO steps, % and (simple). My problem is the last step mentioned for installation of wideband, when I choose wideband LC-1, 0-5v's (calibrating AFR under tools) It runs a bunch of numbers and goes back to the narrowband heading of the drop down menu? MS is powered up.
MS II will not calibrate AFR for WB under tools?
Forum rules
Read the manual to see if your question is answered there before posting. Many users will not reply if the answer is already available in the manual.
If your question is about troubleshooting, configuration, or tuning, you MUST include your processor type (MS-I or MS-II) and code version in your post. If your question is about PCB assembly or modifications, you must also include the main board version number (1.01, 2.2 or 3.0).
If you have questions about MS1/Extra or MS2/Extra code configuration or tuning, please post them at www.msextra.com Such questions posted here will be moved to: a temporary MSextra sub-forum, where they will be removed after 7 days
The full forum rules are here: Forum Rules, be sure to read them all regularly.
Read the manual to see if your question is answered there before posting. Many users will not reply if the answer is already available in the manual.
If your question is about troubleshooting, configuration, or tuning, you MUST include your processor type (MS-I or MS-II) and code version in your post. If your question is about PCB assembly or modifications, you must also include the main board version number (1.01, 2.2 or 3.0).
If you have questions about MS1/Extra or MS2/Extra code configuration or tuning, please post them at www.msextra.com Such questions posted here will be moved to: a temporary MSextra sub-forum, where they will be removed after 7 days
The full forum rules are here: Forum Rules, be sure to read them all regularly.
-
oughtsix
- MegaSquirt Newbie
- Posts: 25
- Joined: Tue Feb 28, 2006 6:44 pm
- Location: Redmond, Oregon
- Contact:
Re: MS II will not calibrate AFR for WB under tools?
I had the same problem way back when. Forget what it was though.
Did you setup the settings.ini file for LC-1 wideband in mega config program?
Did you setup the settings.ini file for LC-1 wideband in mega config program?
1980 450slc converted to MegaSquirt electronic fuel injection and couldn't be happier! Using the stock dizzy and a MSD 6AL ignition along with the stock Bosch ignition box. Home built fuel rails out of aluminum fuel rail stock. Using 19lb mustang injectors I purchased off of ebay.
--Mike.
--Mike.
-
Matt Cramer
- Super Squirter
- Posts: 2951
- Joined: Sat Jul 03, 2004 11:35 am
Re: MS II will not calibrate AFR for WB under tools?
Which menu is this? It doesn't really "remember" the settings on the Calibrate AFR Table menu in MegaTune but they are stored in the MS.wiseguy wrote:Hello,
I installed an LC-1 wideband O2 on my MS II. I changed from narrow band to LC-1 wideband in the configurator file, and the virtual dash displays correct voltage range for wideband. I have set the EGO steps, % and (simple). My problem is the last step mentioned for installation of wideband, when I choose wideband LC-1, 0-5v's (calibrating AFR under tools) It runs a bunch of numbers and goes back to the narrowband heading of the drop down menu? MS is powered up.
Re: MS II will not calibrate AFR for WB under tools?
Thanks Matt,
Like you say it doesn't remember, but everything seems to work fine.
Thanks
Like you say it doesn't remember, but everything seems to work fine.
Thanks
Matt Cramer wrote:Which menu is this? It doesn't really "remember" the settings on the Calibrate AFR Table menu in MegaTune but they are stored in the MS.wiseguy wrote:Hello,
I installed an LC-1 wideband O2 on my MS II. I changed from narrow band to LC-1 wideband in the configurator file, and the virtual dash displays correct voltage range for wideband. I have set the EGO steps, % and (simple). My problem is the last step mentioned for installation of wideband, when I choose wideband LC-1, 0-5v's (calibrating AFR under tools) It runs a bunch of numbers and goes back to the narrowband heading of the drop down menu? MS is powered up.
Re: MS II will not calibrate AFR for WB under tools?
Yes I did,
Its like Matt said it doesn't remember it in the AFR calibration, but it retains it in MS and works fine. Thank You
Its like Matt said it doesn't remember it in the AFR calibration, but it retains it in MS and works fine. Thank You
oughtsix wrote:I had the same problem way back when. Forget what it was though.
Did you setup the settings.ini file for LC-1 wideband in mega config program?