ms2 on supercharged 406 sbc
Forum rules
Read the manual to see if your question is answered there before posting. Many users will not reply if the answer is already available in the manual.
If your question is about troubleshooting, configuration, or tuning, you MUST include your processor type (MS-I or MS-II) and code version in your post. If your question is about PCB assembly or modifications, you must also include the main board version number (1.01, 2.2 or 3.0).
If you have questions about MS1/Extra or MS2/Extra code configuration or tuning, please post them at www.msextra.com Such questions posted here will be moved to: a temporary MSextra sub-forum, where they will be removed after 7 days
The full forum rules are here: Forum Rules, be sure to read them all regularly.
Read the manual to see if your question is answered there before posting. Many users will not reply if the answer is already available in the manual.
If your question is about troubleshooting, configuration, or tuning, you MUST include your processor type (MS-I or MS-II) and code version in your post. If your question is about PCB assembly or modifications, you must also include the main board version number (1.01, 2.2 or 3.0).
If you have questions about MS1/Extra or MS2/Extra code configuration or tuning, please post them at www.msextra.com Such questions posted here will be moved to: a temporary MSextra sub-forum, where they will be removed after 7 days
The full forum rules are here: Forum Rules, be sure to read them all regularly.
-
prostreeted49
- MegaSquirt Newbie
- Posts: 3
- Joined: Tue Oct 12, 2010 5:39 pm
ms2 on supercharged 406 sbc
how are all you guys doin? im new to mega squirt been reading about the ms 2 for about 6 hours, and i still have unresolved questions. my set up is a mpfi system that consists of 60lbs siemans injectors, edelbrock victor e efi manifold, a throttle body elbow with a ported LS1 thottle body. my ignition system is MSD 6AL-2 with a 85551 distributor (just a pickup in the dizzy) i plan to run the mega squirt 2 but i dont want to allow the mega squirt to control the ingnition. do i just hook the tach output to the relay bord like the MS1? also are the any mods that i have to complete inorder to use a stepper motor style IAC?
-
Matt Cramer
- Super Squirter
- Posts: 2951
- Joined: Sat Jul 03, 2004 11:35 am
Re: ms2 on supercharged 406 sbc
Sure, that setup will work fine with MS2 as well as MS1.
You'll need to have the stepper IAC jumpers from assembly step 22 in place. Most preassembled MS2s have these by default.
You'll need to have the stepper IAC jumpers from assembly step 22 in place. Most preassembled MS2s have these by default.
-
prostreeted49
- MegaSquirt Newbie
- Posts: 3
- Joined: Tue Oct 12, 2010 5:39 pm
Re: ms2 on supercharged 406 sbc
thanks for the help! also im running an AEM UEGO wideband, i would use the out put wire off the o2 and connect it to the relay board?
-
prostreeted49
- MegaSquirt Newbie
- Posts: 3
- Joined: Tue Oct 12, 2010 5:39 pm
Re: ms2 on supercharged 406 sbc
also right now i have a b&g 2.21 version (ms1) and plan to upgrade to the mst chip. im gussing i still have to install the jumpers
-
Matt Cramer
- Super Squirter
- Posts: 2951
- Joined: Sat Jul 03, 2004 11:35 am
Re: ms2 on supercharged 406 sbc
You got it. And yes, you'll need to add the jumpers when upgrading.prostreeted49 wrote:thanks for the help! also im running an AEM UEGO wideband, i would use the out put wire off the o2 and connect it to the relay board?