Need some help
Facts:
Have working V2.2 board with MS1 processor, no issues. Loads, works great with stimulator. Can run and interact with Megatune and Tuner studio. No problems.
Purchase a MS2 V3.01, followed instruction from http://www.megasquirt.info/ to a T.
1) Place MegaSquirt-II™ into the 40 pin socket.
2) Be sure the bootloader jumper is in place.
3) Power up your MegaSquirt® controller.
4) 'Run' the file, and follow the directions that come up. This will install the downloader.
I have a MS2 Blue Board, therefore assuming I need the Monitor_v2.905.abs.s19 file.
Below is the message I get:
MegaSquirt Download 2.00
Reading C:/Documents and Settings/Fred/Desktop/Monitor_v2.905.abs.s19:
Detected MS-II (HCS12) code.
Entry point: 0x0000
Code range : 0x4000-0x3db360
File read successfully.
Opened comm port 2 at 115200.
ERROR: Timed out reading response, 0xE0
Elapsed time: 13.88 seconds
Tried comm port 1 and 3 (both work with my MS1 processor without issues. Same results.
Also I have LED PUMP and INJ2 light up on the stimulator board when MS2 is in, boot Jumper in.
Any thoughts??????????
A million thank you
MS2 HELP needed. unable to load Boatloading program in MS2
Forum rules
Read the manual to see if your question is answered there before posting. Many users will not reply if the answer is already available in the manual.
If your question is about troubleshooting, configuration, or tuning, you MUST include your processor type (MS-I or MS-II) and code version in your post. If your question is about PCB assembly or modifications, you must also include the main board version number (1.01, 2.2 or 3.0).
If you have questions about MS1/Extra or MS2/Extra code configuration or tuning, please post them at www.msextra.com Such questions posted here will be moved to: a temporary MSextra sub-forum, where they will be removed after 7 days
The full forum rules are here: Forum Rules, be sure to read them all regularly.
Read the manual to see if your question is answered there before posting. Many users will not reply if the answer is already available in the manual.
If your question is about troubleshooting, configuration, or tuning, you MUST include your processor type (MS-I or MS-II) and code version in your post. If your question is about PCB assembly or modifications, you must also include the main board version number (1.01, 2.2 or 3.0).
If you have questions about MS1/Extra or MS2/Extra code configuration or tuning, please post them at www.msextra.com Such questions posted here will be moved to: a temporary MSextra sub-forum, where they will be removed after 7 days
The full forum rules are here: Forum Rules, be sure to read them all regularly.
-
Bernard Fife
- Master Squirter
- Posts: 475
- Joined: Thu Oct 29, 2009 12:54 pm
Re: MS2 HELP needed. unable to load Boatloading program in M
"Never wrestle with pigs. You both get dirty and the pig likes it.” - George Bernard Shaw
-
Flatblackfanatic
- MegaSquirt Newbie
- Posts: 7
- Joined: Sun Sep 11, 2011 4:35 pm
Re: MS2 HELP needed. unable to load Boatloading program in M
I was online looking for a solution to the same problem... I was about to send out my daughterboard to get checked out, but I decided that maybe my power supply could be the problem. I swapped to a yamaha keyboard adapter, specifically DC 12V, 700ma.
I plugged it in, restarted the loader and successfully installed my file you mentioned. no problem. =)
I saw your comment, and once I figured mine out I felt like It could help, I hope it does!
I plugged it in, restarted the loader and successfully installed my file you mentioned. no problem. =)
I saw your comment, and once I figured mine out I felt like It could help, I hope it does!