hey guys i got my car running
95 hyundai scoupe turbo
1.5l turbo
500cc high imp inj
walbro 255
ms2 v3 fuel only
tuner studio un reg < is it worth it to pay ?
car runs at about 14.7 +- a little
but when i get into a little bit of boost i no longer see the dot on the ve table :S
so i dont know what to do here is a datalog of a drive down the street
if some one could hel and point me in the right dirr plz
some one that knows what there doing plz
Forum rules
Read the manual to see if your question is answered there before posting. Many users will not reply if the answer is already available in the manual.
If your question is about troubleshooting, configuration, or tuning, you MUST include your processor type (MS-I or MS-II) and code version in your post. If your question is about PCB assembly or modifications, you must also include the main board version number (1.01, 2.2 or 3.0). For tuning/troubleshooting questions, please attached a datalog and your MSQ file to your post.
If you have questions about MS1/Extra or MS2/Extra code configuration or tuning, please post them at www.msextra.com Such questions posted here will be moved to: a temporary MSextra sub-forum, where they will be removed after 7 days
The full forum rules are here: Forum Rules, be sure to read them all regularly.
Read the manual to see if your question is answered there before posting. Many users will not reply if the answer is already available in the manual.
If your question is about troubleshooting, configuration, or tuning, you MUST include your processor type (MS-I or MS-II) and code version in your post. If your question is about PCB assembly or modifications, you must also include the main board version number (1.01, 2.2 or 3.0). For tuning/troubleshooting questions, please attached a datalog and your MSQ file to your post.
If you have questions about MS1/Extra or MS2/Extra code configuration or tuning, please post them at www.msextra.com Such questions posted here will be moved to: a temporary MSextra sub-forum, where they will be removed after 7 days
The full forum rules are here: Forum Rules, be sure to read them all regularly.
some one that knows what there doing plz
You do not have the required permissions to view the files attached to this post.
Re: some one that knows what there doing plz
and here is the msq
You do not have the required permissions to view the files attached to this post.
-
kjones6039
- Master Squirter
- Posts: 618
- Joined: Sat Jul 22, 2006 7:02 pm
- Location: Eureka, Nevada USA
- Contact:
Re: some one that knows what there doing plz
Absolutely!!!!!tuner studio un reg < is it worth it to pay ?
Ken
1979 Corvette - 383 CID SBC w/ Holley Pro-Jection 900 CFM TBI, 4-85 lb lo-z injectors & Walbro 255 pump
MS2 v3 w/ms2extra 3.4.0 Release
36-1, Delphi LS2/7 coils in wasted spark, driven by v2.0 logic board from JBPerformance
Spartan Lambda Sensor from 14point7
MS2 v3 w/ms2extra 3.4.0 Release
36-1, Delphi LS2/7 coils in wasted spark, driven by v2.0 logic board from JBPerformance
Spartan Lambda Sensor from 14point7
Re: some one that knows what there doing plz
I'm not well up on turbos, but all your tables, VE, AFR, IGN appear to be for a naturally aspirated engine. I'd expect to see the max kPa to read at least your max boost. But I'm only guessing.
Dave P, London UK.
Rover V-8
MSII V3
EDIS
Tech Edge Wideband
Rover V-8
MSII V3
EDIS
Tech Edge Wideband
Re: some one that knows what there doing plz
yea i found my issue my kPa was set up 100 when it shoud be upto 150 kPa
this can get a little frustraiting but atleast in runs ok without boost
tonight i wil reset the tables and try to getinto some boost thanks guys
this can get a little frustraiting but atleast in runs ok without boost
tonight i wil reset the tables and try to getinto some boost thanks guys