Edelbrock proflo 1

This is the place to ask general MegaSquirt® questions if you are just getting started.
Please read the FAQ and MegaManual before posting. Also see the Forum Rules. Click this link for Purchasing information.
If you are looking for MS-extra or MS-3 information, please post here: www.msextra.com
Forum rules
Read the manual to see if your question is answered there before posting. Many users will not reply if the answer is already available in the manual.

If your question is about troubleshooting, configuration, or tuning, you MUST include your processor type (MS-I or MS-II) and code version in your post. If your question is about PCB assembly or modifications, you must also include the main board version number (1.01, 2.2 or 3.0).

If you have questions about MS1/Extra or MS2/Extra code configuration or tuning, please post them at www.msextra.com Such questions posted here will be moved to: a temporary MSextra sub-forum, where they will be removed after 7 days

The full forum rules are here: Forum Rules, be sure to read them all regularly.
Post Reply
Nabes68
MegaSquirt Newbie
Posts: 4
Joined: Tue Sep 25, 2012 5:22 am

Edelbrock proflo 1

Post by Nabes68 »

What is the best ms to get to go with proflo 1 it's on a 1968 ford bronco with a rebuilt 302 .030 over rv cam and I think 194 valves I can not get this proflo dialed in to save my life
Top
kjones6039
Master Squirter
Posts: 618
Joined: Sat Jul 22, 2006 7:02 pm
Location: Eureka, Nevada USA
Contact:
Contact kjones6039

Re: Edelbrock proflo 1

Post by kjones6039 »

Curious.......

What are you using to manage the proflo now?

Ken
1979 Corvette - 383 CID SBC w/ Holley Pro-Jection 900 CFM TBI, 4-85 lb lo-z injectors & Walbro 255 pump
MS2 v3 w/ms2extra 3.4.0 Release
36-1, Delphi LS2/7 coils in wasted spark, driven by v2.0 logic board from JBPerformance
Spartan Lambda Sensor from 14point7
Top
Nabes68
MegaSquirt Newbie
Posts: 4
Joined: Tue Sep 25, 2012 5:22 am

Re: Edelbrock proflo 1

Post by Nabes68 »

It is edelbrock I think it's all gm stuff it runs good but not as good as it should and tuning is a pain the the butt and its not wide band o2 and to upgrade to tune with a laptop it's going to be 1500$ plus
Top
kjones6039
Master Squirter
Posts: 618
Joined: Sat Jul 22, 2006 7:02 pm
Location: Eureka, Nevada USA
Contact:
Contact kjones6039

Re: Edelbrock proflo 1

Post by kjones6039 »

Nabes68 wrote:It is edelbrock I think it's all gm stuff it runs good but not as good as it should and tuning is a pain the the butt and its not wide band o2 and to upgrade to tune with a laptop it's going to be 1500$ plus
That has been pretty much my total experience with those high $$$ management systems!

There are any number of MS and firmware versions out there that would run your Edelbrock quite nicely. I suggest you take a look at this link to get an idea of which MS might suit your needs.

http://www.msextra.com/feature-xref.html

Good luck!

Ken
1979 Corvette - 383 CID SBC w/ Holley Pro-Jection 900 CFM TBI, 4-85 lb lo-z injectors & Walbro 255 pump
MS2 v3 w/ms2extra 3.4.0 Release
36-1, Delphi LS2/7 coils in wasted spark, driven by v2.0 logic board from JBPerformance
Spartan Lambda Sensor from 14point7
Top
Nabes68
MegaSquirt Newbie
Posts: 4
Joined: Tue Sep 25, 2012 5:22 am

Re: Edelbrock proflo 1

Post by Nabes68 »

And one of my biggest complaints is I only get 10mpg I can get that with a 2 Barrel Holly and it hard to tune you have to drive it and look at a light that flashes, vacuum reading and rpm. There is no good mapping they give you a chart to write in to map it while driving
Top
kjones6039
Master Squirter
Posts: 618
Joined: Sat Jul 22, 2006 7:02 pm
Location: Eureka, Nevada USA
Contact:
Contact kjones6039

Re: Edelbrock proflo 1

Post by kjones6039 »

Nabes68 wrote:And one of my biggest complaints is I only get 10mpg I can get that with a 2 Barrel Holly and it hard to tune you have to drive it and look at a light that flashes, vacuum reading and rpm. There is no good mapping they give you a chart to write in to map it while driving
More good reasons to switch to MS IMO!

Ken
1979 Corvette - 383 CID SBC w/ Holley Pro-Jection 900 CFM TBI, 4-85 lb lo-z injectors & Walbro 255 pump
MS2 v3 w/ms2extra 3.4.0 Release
36-1, Delphi LS2/7 coils in wasted spark, driven by v2.0 logic board from JBPerformance
Spartan Lambda Sensor from 14point7
Top
Nabes68
MegaSquirt Newbie
Posts: 4
Joined: Tue Sep 25, 2012 5:22 am

Re: Edelbrock proflo 1

Post by Nabes68 »

I think I have everything to do it I just need a ms ecu and some other odds and ends
Top
kjones6039
Master Squirter
Posts: 618
Joined: Sat Jul 22, 2006 7:02 pm
Location: Eureka, Nevada USA
Contact:
Contact kjones6039

Re: Edelbrock proflo 1

Post by kjones6039 »

Nabes68 wrote:I think I have everything to do it I just need a ms ecu and some other odds and ends
I would suspect that any/all of the sensors that came with the Edelbrock will be fine for MS.

Ken
1979 Corvette - 383 CID SBC w/ Holley Pro-Jection 900 CFM TBI, 4-85 lb lo-z injectors & Walbro 255 pump
MS2 v3 w/ms2extra 3.4.0 Release
36-1, Delphi LS2/7 coils in wasted spark, driven by v2.0 logic board from JBPerformance
Spartan Lambda Sensor from 14point7
Top
MonzaRacer
MegaSquirt Newbie
Posts: 8
Joined: Wed May 11, 2011 7:29 pm

Re: Edelbrock proflo 1

Post by MonzaRacer »

Edelbrock computer is built by Magneti Marelli. And since most sensors are probably GM or Ford MS should work with any of them. Dont remeber but I believe Pro Flo runs either GM or Chrysler 4.0 IAC.
MS-II V3.0 or MS-3 should be awesome.
Top
Post Reply

Return to “General Information”