True - thank you for pointing that out.
Now if only I can find new plug ends I may be makaing sparks this weekend. My plan was to firing it up as EDIS only to see if it runs then interface MSII with it. Tryign to limit my variable. With the static 10 degree timing I think it should start and idle fine since I am only running about 12 degrees now.
EDIS Wiring Questions
Forum rules
Read the manual to see if your question is answered there before posting. Many users will not reply if the answer is already available in the manual.
If your question is about troubleshooting, configuration, or tuning, you MUST include your processor type (MS-I or MS-II) and code version in your post. If your question is about PCB assembly or modifications, you must also include the main board version number (1.01, 2.2 or 3.0). For tuning/troubleshooting questions, please attached a datalog and your MSQ file to your post.
If you have questions about MS1/Extra or MS2/Extra code configuration or tuning, please post them at www.msextra.com Such questions posted here will be moved to: a temporary MSextra sub-forum, where they will be removed after 7 days
The full forum rules are here: Forum Rules, be sure to read them all regularly.
Read the manual to see if your question is answered there before posting. Many users will not reply if the answer is already available in the manual.
If your question is about troubleshooting, configuration, or tuning, you MUST include your processor type (MS-I or MS-II) and code version in your post. If your question is about PCB assembly or modifications, you must also include the main board version number (1.01, 2.2 or 3.0). For tuning/troubleshooting questions, please attached a datalog and your MSQ file to your post.
If you have questions about MS1/Extra or MS2/Extra code configuration or tuning, please post them at www.msextra.com Such questions posted here will be moved to: a temporary MSextra sub-forum, where they will be removed after 7 days
The full forum rules are here: Forum Rules, be sure to read them all regularly.
Re: EDIS Wiring Questions
pcf_mark wrote:True - thank you for pointing that out.
Now if only I can find new plug ends I may be makaing sparks this weekend. My plan was to firing it up as EDIS only to see if it runs then interface MSII with it. Tryign to limit my variable. With the static 10 degree timing I think it should start and idle fine since I am only running about 12 degrees now.
If you want a 'limp home' setting of 12 BTDC, there's no reason why you shouldn't set the trigger wheel to that.
Dave P, London UK.
Rover V-8
MSII V3
EDIS
Tech Edge Wideband
Rover V-8
MSII V3
EDIS
Tech Edge Wideband
Re: EDIS Wiring Questions
I am hoping this is my last wiring question for the EDIS! I have almost everything wired and mounted and I am looking at the coils for the firing order and plug wires.
I know the firing order is 1 5 4 2 6 3 7 8
I know the coils fire A B C D A B C D etc
I also know to pair the wasted with power stroked for I will have 1-6, 5-3, 4-7, 2-8 on the same coils
I also know which set of coils is A-B and which is C-D based on how they are wired. What I do not know if which of the two coils A-B is actually A so I can get my wires started. The markings are not clear. The wire that goes from pin 8 to the A-B pack goes to the left coil is coil A?
Thanks for all your help!
I know the firing order is 1 5 4 2 6 3 7 8
I know the coils fire A B C D A B C D etc
I also know to pair the wasted with power stroked for I will have 1-6, 5-3, 4-7, 2-8 on the same coils
I also know which set of coils is A-B and which is C-D based on how they are wired. What I do not know if which of the two coils A-B is actually A so I can get my wires started. The markings are not clear. The wire that goes from pin 8 to the A-B pack goes to the left coil is coil A?
Thanks for all your help!
Re: EDIS Wiring Questions
This is for my Rover V8.
Dave P, London UK.
Rover V-8
MSII V3
EDIS
Tech Edge Wideband
Rover V-8
MSII V3
EDIS
Tech Edge Wideband
Re: EDIS Wiring Questions
It runs! It runs! It runs!
I sorted out the coil thanks to that diagram confirming it. Start on the first try! No fuss no spittig! Woo hoo!
Thanks for all your help. Now I am going to finalize the wiring for the MSII then I'll be tuning the ignition.
I sorted out the coil thanks to that diagram confirming it. Start on the first try! No fuss no spittig! Woo hoo!
Thanks for all your help. Now I am going to finalize the wiring for the MSII then I'll be tuning the ignition.