2.883i code, new "Other Fuel Settings" stuff

lmacneill · Post by **lmacneill** » Thu Jan 24, 2008 4:14 pm

I just installed the 2.883i code on my MS-II, and updated the .ini files for MegaTune. Everything (software-wise) seems to be fine so far. (Haven't actually installed the computer back into the car yet, so I don't know how it'll affect the running of the car... But I'm sure it'll probably be fine... I manually copied the data from my existing MSQ file to a totally new one, to avoid any incompatibilities there... And imported the VE & AFR tables after exporting them from the old MSQ file...)

Anyway, the question I have is: there are a couple of new settings in MegaTune that aren't explained in the manual (at least, I couldn't find them) and that aren't self-explanatory (at least not to me). Under Fuel Set-up | Other Fuel Settings, there is "Additional Fuel (switched by E0 low or cyclic)" and "Additional Fuel (cyclc only)." What do these two things do?

Thanks,

grippo · Post by **grippo** » Fri Jan 25, 2008 6:30 am

when shifting codes like this, when in doubt leave the defaults. The two items you referred to are for experimental use. They can provide extra fuel for Nitrous use or they can be used to provide a measured increase in fuel that can be used to test the response of the EGO system.

lmacneill · Post by **lmacneill** » Sat Jan 26, 2008 5:29 pm

Oh neat! I left 'em at the default of zero anyway -- but it's good to know what they're for.

Thanks,

msoultan · Post by **msoultan** » Wed Dec 03, 2008 11:33 pm

grippo wrote:when shifting codes like this, when in doubt leave the defaults. The two items you referred to are for experimental use. They can provide extra fuel for Nitrous use or they can be used to provide a measured increase in fuel that can be used to test the response of the EGO system.

Hey Al,
Is there any documentation for the Additional Fuel settings? While I did seem to get some pretty good results when I built my VE table "ledge" for measuring my EGO delay, I thought I'd give your additional fuel settings feature a try to confirm my results.

Ok, under the menu Additional fuel (switched by E0 or cyclic) I see the following option:

Fuel added to base PW (msec)

I understand that it will add that value to the base PW when the additional fuel is triggered - that part's easy. What I don't get is If you specify a value for both of the items under Additional Fuel (cyclic only), will it pulse every number of specified seconds AND the number of specified cycles?

I guess what's also confusing is the word cyclic - is that referring to the number of cycles or the fact that it's cyclical in nature (repeating every number of cycles or number of seconds)?

Also, what's E0? I'm guessing that's an input into the processor?

Thanks,
Mike

grippo · Post by **grippo** » Thu Dec 04, 2008 9:08 am

Mike,

The logic for the extra pulsewidth for x-tau tuning is as follows:

Deliver the specified additional pw amount for the specified number of tach cycles, then resume normal operation for specified number of seconds to allow all to clear, then repeat forever.

To kill the process, set the specified additional pw amount to 0, then zero the specified number of wait seconds.

E0 is the port pin on the processor - you can trace it to the connector pin from the schematic. It is only used as an input for flex fuel or for N2O enrichment.

msoultan · Post by **msoultan** » Thu Dec 04, 2008 9:21 am

Ahh.. ok.

To make things a little easier to understand to the first-time looker, you might want to swap "Time between added fuel" and "Number of cycles" and then rename "Number of cycles" to "Number of cycles to add fuel". Minor, but might make things a little easier to understand...

I'm going to give it a try today. Thanks for adding that feature - should come in very handy!

Mike

MSefi.com read only forum (Jan.15,2018)

2.883i code, new "Other Fuel Settings" stuff

2.883i code, new "Other Fuel Settings" stuff

Re:

Re: 2.883i code, new "Other Fuel Settings" stuff

Re: 2.883i code, new "Other Fuel Settings" stuff