Hello:
Newly mounted my valve of relenti pwm bosch, with a card of glensgaraje and doing the first tests it seems to work likely but only a thing, in the cranking it does not seem that it opens 100 %, and fact datalog and changes the opening with the temperature but in the cranking it does not open.
Ms2 and v3 with code 2883, the frequency in 80 the valve turns slow if the frequency is + high of 120 seems that the valve throbs on having opened and to close to ceiling.
And position in cranking position in megatune 100, which I believe is 100 % of opened, or I am wrong.
And that the this valve opened 100 and closed to 0.
If someone can help me.
Valve of relenti 3 cables pwm with targeta of glens garage
Forum rules
Read the manual to see if your question is answered there before posting. Many users will not reply if the answer is already available in the manual.
If your question is about troubleshooting, configuration, or tuning, you MUST include your processor type (MS-I or MS-II) and code version in your post. If your question is about PCB assembly or modifications, you must also include the main board version number (1.01, 2.2 or 3.0). For tuning/troubleshooting questions, please attached a datalog and your MSQ file to your post.
If you have questions about MS1/Extra or MS2/Extra code configuration or tuning, please post them at www.msextra.com Such questions posted here will be moved to: a temporary MSextra sub-forum, where they will be removed after 7 days
The full forum rules are here: Forum Rules, be sure to read them all regularly.
Read the manual to see if your question is answered there before posting. Many users will not reply if the answer is already available in the manual.
If your question is about troubleshooting, configuration, or tuning, you MUST include your processor type (MS-I or MS-II) and code version in your post. If your question is about PCB assembly or modifications, you must also include the main board version number (1.01, 2.2 or 3.0). For tuning/troubleshooting questions, please attached a datalog and your MSQ file to your post.
If you have questions about MS1/Extra or MS2/Extra code configuration or tuning, please post them at www.msextra.com Such questions posted here will be moved to: a temporary MSextra sub-forum, where they will be removed after 7 days
The full forum rules are here: Forum Rules, be sure to read them all regularly.
-
valenciano
- Helpful Squirter
- Posts: 43
- Joined: Fri Sep 05, 2008 12:44 pm
-
valenciano
- Helpful Squirter
- Posts: 43
- Joined: Fri Sep 05, 2008 12:44 pm
Re: Valve of relenti 3 cables pwm with targeta of glens garage
I think one thing and done wrong:
with the circuit glensgarage valve for pwm 3 wires in the v3 with MS2 amendment that needs to be done:
1-stop circuit as if it were an on-off valve and connect the output of MS2 to the circuit glensgarage.
2-make changes to a valve pwm and connect the output of MS2 to glensgarage circuit.
and I made the point 1 and why this might be so I'm not functioning well at all?
with the circuit glensgarage valve for pwm 3 wires in the v3 with MS2 amendment that needs to be done:
1-stop circuit as if it were an on-off valve and connect the output of MS2 to the circuit glensgarage.
2-make changes to a valve pwm and connect the output of MS2 to glensgarage circuit.
and I made the point 1 and why this might be so I'm not functioning well at all?
-
Glen Hoag
Re: Valve of relenti 3 cables pwm with targeta of glens garage
Connect the FIDLE pad of the 3-wire idle board to MS2 FIDLE output.valenciano wrote:I think one thing and done wrong:
with the circuit glensgarage valve for pwm 3 wires in the v3 with MS2 amendment that needs to be done:
1-stop circuit as if it were an on-off valve and connect the output of MS2 to the circuit glensgarage.
2-make changes to a valve pwm and connect the output of MS2 to glensgarage circuit.
and I made the point 1 and why this might be so I'm not functioning well at all?
Connect ISV1 pad to the idle valve "open" coil.
Connect ISV2 pad to the idle valve "close" coil.
Connect idle valve common pin to switched +12v (on in start and run).
Set the idle valve type to PWM.
Set PWM frequency to whatever the OEM used for smooth operation. (typically 100Hz-200Hz).
Set PWM limits to 0% and 100%
This should work, though you may have to experiment with the limits.
--Glen
-
valenciano
- Helpful Squirter
- Posts: 43
- Joined: Fri Sep 05, 2008 12:44 pm
Re: Valve of relenti 3 cables pwm with targeta of glens garage
ok, is already done, but in v3 MS2 circuit that must be done on-or off pwm?
thanks.
thanks.
-
valenciano
- Helpful Squirter
- Posts: 43
- Joined: Fri Sep 05, 2008 12:44 pm
Re: Valve of relenti 3 cables pwm with targeta of glens garage
and supplied with the changes said the manual for v3 and pwm but so does not work, the manual says ms2extra different changes for pwm because, it seems that has v3 to be with and assembly of on-off valve, someone mounted circuit glesgarage and I can say that we must do in v3.
-
valenciano
- Helpful Squirter
- Posts: 43
- Joined: Fri Sep 05, 2008 12:44 pm
Re: Valve of relenti 3 cables pwm with targeta of glens garage
Solved:
I have proved both assemblie in it v3 and the circ uit of glensgarage works with the assembly of on-off.
My valve was closing 36 % and it opened to 76 %, this way the step mas small was of closing and the step of take-off was not working, I changed the cables into the circuit of glensgarage and it
has arranged, now it opens to ceiling in the take-off and then it closes little by little to the temperature of the table.
I have proved it in the estimulador and in order that it works well it is necessary to put the same nourishment to the ms and the valve, I put a battery for both things with a fuse.
I have proved both assemblie in it v3 and the circ uit of glensgarage works with the assembly of on-off.
My valve was closing 36 % and it opened to 76 %, this way the step mas small was of closing and the step of take-off was not working, I changed the cables into the circuit of glensgarage and it
has arranged, now it opens to ceiling in the take-off and then it closes little by little to the temperature of the table.
I have proved it in the estimulador and in order that it works well it is necessary to put the same nourishment to the ms and the valve, I put a battery for both things with a fuse.