BMW M50 No Start
Forum rules
Read the manual to see if your question is answered there before posting. Many users will not reply if the answer is already available in the manual.
If your question is about troubleshooting, configuration, or tuning, you MUST include your processor type (MS-I or MS-II) and code version in your post. If your question is about PCB assembly or modifications, you must also include the main board version number (1.01, 2.2 or 3.0). For tuning/troubleshooting questions, please attached a datalog and your MSQ file to your post.
If you have questions about MS1/Extra or MS2/Extra code configuration or tuning, please post them at www.msextra.com Such questions posted here will be moved to: a temporary MSextra sub-forum, where they will be removed after 7 days
The full forum rules are here: Forum Rules, be sure to read them all regularly.
Read the manual to see if your question is answered there before posting. Many users will not reply if the answer is already available in the manual.
If your question is about troubleshooting, configuration, or tuning, you MUST include your processor type (MS-I or MS-II) and code version in your post. If your question is about PCB assembly or modifications, you must also include the main board version number (1.01, 2.2 or 3.0). For tuning/troubleshooting questions, please attached a datalog and your MSQ file to your post.
If you have questions about MS1/Extra or MS2/Extra code configuration or tuning, please post them at www.msextra.com Such questions posted here will be moved to: a temporary MSextra sub-forum, where they will be removed after 7 days
The full forum rules are here: Forum Rules, be sure to read them all regularly.
-
Wheelandrimrepair
- MegaSquirt Newbie
- Posts: 8
- Joined: Thu Sep 01, 2011 4:19 pm
BMW M50 No Start
Hello Megasquirtees I am new and just put it on my boosted 1992 BMW. I have MSII V 3 Board and it will not start. I have Spark, and Injector pulse but it seems to be kicking back on cranking. I adjusted every setting under the sun up and down, to no avail. Can I get a good pointer, kinda outa ideas here, worn out! about to put it to the side again
-
kjones6039
- Master Squirter
- Posts: 618
- Joined: Sat Jul 22, 2006 7:02 pm
- Location: Eureka, Nevada USA
- Contact:
Re: BMW M50 No Start
Where is your initial timing set? Your description sounds like it is too far adavnced.
Ken
Ken
1979 Corvette - 383 CID SBC w/ Holley Pro-Jection 900 CFM TBI, 4-85 lb lo-z injectors & Walbro 255 pump
MS2 v3 w/ms2extra 3.4.0 Release
36-1, Delphi LS2/7 coils in wasted spark, driven by v2.0 logic board from JBPerformance
Spartan Lambda Sensor from 14point7
MS2 v3 w/ms2extra 3.4.0 Release
36-1, Delphi LS2/7 coils in wasted spark, driven by v2.0 logic board from JBPerformance
Spartan Lambda Sensor from 14point7
-
Wheelandrimrepair
- MegaSquirt Newbie
- Posts: 8
- Joined: Thu Sep 01, 2011 4:19 pm
Re: BMW M50 No Start
Initial Timing setting? hmmmm To be honest I do not know if I even set that as yet. I have been in and out of tuner studio and do not remember seeing a setting called initial timing or a procedure. Please forgive my inexperience, really steep learning cure, so many new things to get up to speed with. I did do the trigger wheel setting for my 60-2 crank wheel and under cranking I set the skip pulses to 20. So I am wondering if that is what you meant