MSefi.com read only forum (Jan.15,2018)

Plugs look good Matt, No signs of running lean at all...I have no idea what could be causing this....

Matt,

I don't think its in the tune...It doesn't matter how much I turn on VE or Req fuel...no change..If I drove up to the shop do you think you would be able to help me out with the computer again? Do yall accept trade-ins? lol...j/k I've tried everything I can think of at this point...and ...

Matt,

I did the injector test and the car will run on test mode also...It doesn't matter what I do to VE or required fuel...it starts and just dies. I don't know what is causing the fuel to stop. Since it will run on test mode does this confirm that the flyback board and everything is ok? I just ...

Yes I get signal...the left one flashes correctly and the right one turns on when I push the gas...

So maybe its suppossed to be on and I have another issue?

Matt,

I re soldered the 12v supply to the flyback board but still cant keep the car running. All three lights flash when powered up...everything looks good in megatune but then when I try to crank the middle light stays on and I'm not getting fuel. What do you think is going on? Or what should I do ...

Matt,

I found where it is supposed to be connected. BUT....when I was putting it on I pulled one of the wired off the flyback board and even after re soldering it...I can't get the car to run now....the Middle light is staying on. It is the 12v supply for the flyback board...when I did it the ...

I'm trying to figure that out now. I don't see anything jumpered to pin 36 now So I'm not sure. But I really don't know what I'm looking at.

Matt,

Is there a test I can do with a meter on the SAW end comeing from megasquirt to the module? Pin #36 dark brown wire?

Braden

edit: Since this is a MS1 2.2 board with MSII daughter board....is this the right PIN? or should it be something else? This has me a little confused?
V2.2 main board ...

I've the settings verbatum out of megamanual...

In MegaTune, set:

Trigger offset = 0° (this will vary, depending on the wheel/pickup configuration),
Ignition Input Capture to 'Rising Edge', ('Falling Edge' for MicroSquirt® only if using the VR input circuit - not recommmended),
Cranking ...

Matt, What would cause the module not to get the Saw signal? Could this be simple wiring? Since Megatune is showing that it is controlling timing is it from the computer to the module or from the sensor to the module that would be causing my problems? Thanks Matt.

Braden

Hey guys,

First off the computer that I have for tuning I can't post the msq file or a datalog...so try to think past that for me if you can.

Megatune is showing that it is controlling timing according to my ignition map. I've got good tach signal and everything looks good on the laptop. The ...

I will try to datalog and let you know what I can see. I know its not the ASE settings I set the cycles to 0 on the car while its warmed up with no change...What is WUE?

On the ms1 that I was running..Which is from Fuel injectrion Pro. They are no longer in business http://www.fuelinjectionpro.com ...

Yes we are talking about the ms2...the sketchy ms1 is done...nothing to do with the car anymore. I'm taking the ms2 to the megameet....Its the only computer I've been working with...and is what I'll be running the car with.

My sketchy ms1 is sitting in a box. The computer on the car now is a ms 2.2 with the msII daughter card and flyback board on it. I got it used from my car forum. I trust the guy I got it from.

devastator wrote:So, do you have the MS2 onboard right now, and the MS1 is in a box on the dining room table or something?

BOHO wrote:Thanks for the help and advice devastator.

No problem.

Correct.

Thanks for the help and advice devastator. I really appreciate any input I can get. I think what honestly happened here was corruption when I went from a ms1 msq running the original code and loaded it into this ms II computer. And havn't been able to get back to square one. I know the injectors are ...

I was just going to bring the MS...Yeah I was going to look on ebay for something like that. I got the one I'm using now off ebay thinking that I could use the pcmcia slot but the cd drive was damaged and it has no usb ports....the serial is the only thing on it that works right...lol. I figured if ...

I was thinking it was a driver problem...since it would not connect. I don't think I'll be able to get the car there though...was thinking of just bringing the computer itself.

I have bought a pcmcia and couldn't get it to work with this laptop...I had A laptop on XP but it crashed. If I could post the msq or datalog I would. I'm looking for a used one right now so I can help with this problem. Its not an accel issue, I can only get the car to idle on settings that it ...

Is there a reboot I could do on the megasquirt? So that I could start from scratch...Is that possible?