Search found 10 matches

by eluis
Fri Nov 12, 2010 6:10 pm
Forum: MS-II Ignition Setup, Tuning, and Troubleshooting
Topic: Jeep cherokee with MSII No RPM
Replies: 15
Views: 935

Re: Jeep cherokee with MSII No RPM

Well I started the engine all ready and it runs ok, I going to try to use the original ICM module and elliminate the 7 pin HEI taking the VR signal from the distributor and sending the ignition output from pin 36 with a 5 volt pull-up circuit.
I will let you know if it works.
Thanks.
Att.Eluis.
by eluis
Fri Nov 05, 2010 12:23 pm
Forum: MS-II Ignition Setup, Tuning, and Troubleshooting
Topic: Jeep cherokee with MSII No RPM
Replies: 15
Views: 935

Re: Jeep cherokee with MSII No RPM

Hello Matt. I tried to start the engine changing the settings to 22 dase teeth and two missing teeth but the engine would not crank. What I am going to do is to use a 1987 jeep distributor with a 7 pin HEI module. I think that will solve my problem. Any suggestion I will appreciate.
Thanks.
Att Eluis.
by eluis
Sat Oct 30, 2010 4:42 pm
Forum: MS-II Ignition Setup, Tuning, and Troubleshooting
Topic: Jeep cherokee with MSII No RPM
Replies: 15
Views: 935

Re: Jeep cherokee with MSII No RPM

Hello Lance here it is some information about the Jeep flywheel.
by eluis
Sat Oct 30, 2010 1:35 pm
Forum: MS-II Ignition Setup, Tuning, and Troubleshooting
Topic: Jeep cherokee with MSII No RPM
Replies: 15
Views: 935

Re: Jeep cherokee with MSII No RPM

Ok Lance I will check how many teeth has the flywheel. But last monday I was seeing another flywheel that I have and I think that the flywheel has 3 places with missing teeth, and what I saw in the MSII trigger wheel information the trigger wheel only has missing teeth in one place of the wheel. But ...
by eluis
Fri Oct 29, 2010 2:04 pm
Forum: MS-II Ignition Setup, Tuning, and Troubleshooting
Topic: Jeep cherokee with MSII No RPM
Replies: 15
Views: 935

Re: Jeep cherokee with MSII No RPM

I loaded bowling& Groppo code 2.88. I all ready set the ECU type to 1 under fuel set up. I can see all reading and set the wheel decoder setting like these.
21 base teeth
1 missing tooth
21 skip teeth
12 delay teeth
Thanks.
by eluis
Fri Oct 29, 2010 1:04 pm
Forum: MS-II Ignition Setup, Tuning, and Troubleshooting
Topic: Jeep cherokee with MSII No RPM
Replies: 15
Views: 935

Re: Jeep cherokee with MSII No RPM

Sorry, I had wrote before that there is RPM. And the problem is that there is not RPM in megatune and no pulse from Pin 36.
Excuses to all.
Thanks.
Att.Eluis.
by eluis
Thu Oct 28, 2010 3:40 pm
Forum: MS-II Ignition Setup, Tuning, and Troubleshooting
Topic: Jeep cherokee with MSII No RPM
Replies: 15
Views: 935

Jeep cherokee with MSII No RPM

Hello to all.
I recently bought a MSII 3.0 assembled from diyautone to install in a 1988 Jeep Cherokee laredo 4.0l. They are helping lot.I writting here to share with all and to be part of the forum.
The issue that I have now is that there is RPM signal from pin 36. I am using the stock crankshaft ...
by eluis
Fri Jul 25, 2008 6:39 pm
Forum: Tuning Fuel and Air
Topic: How read O2 sensor gauge?
Replies: 4
Views: 434

Re: How read O2 sensor gauge?

Thanks. Bill now I'm more sure when I do tuning.
by eluis
Sat Jul 19, 2008 6:26 pm
Forum: Tuning Fuel and Air
Topic: How read O2 sensor gauge?
Replies: 4
Views: 434

Re: How read O2 sensor gauge?

I'm using the bottom bar, which start in green and finish with red. And sometimes I use the air:fuel ratio gauge that start with 10:00 and finish with 19:40.Really what I want to know is if the engine is rich when is in green and lean when is in red.
Thanks.
by eluis
Sun Jul 13, 2008 10:18 am
Forum: Tuning Fuel and Air
Topic: How read O2 sensor gauge?
Replies: 4
Views: 434

How read O2 sensor gauge?

I want to know how is the mixture when is red in the bottom bar of the main megatune page.I'm not sure if is rich or lean.
I hope somebody help me.
Thanks.
Att. ELuis