can't set the basic table
what's the problem with that?
and thanks for reply
MS new guy
i use sym RV 180 engine(motorcycle engine 171 c.c) with bosch 0 277 100 124 ignition control
can't set basic table
Forum rules
Read the manual to see if your question is answered there before posting. Many users will not reply if the answer is already available in the manual.
If your question is about troubleshooting, configuration, or tuning, you MUST include your processor type (MS-I or MS-II) and code version in your post. If your question is about PCB assembly or modifications, you must also include the main board version number (1.01, 2.2 or 3.0).
If you have questions about MS1/Extra or MS2/Extra code configuration or tuning, please post them at www.msextra.com Such questions posted here will be moved to: a temporary MSextra sub-forum, where they will be removed after 7 days
The full forum rules are here: Forum Rules, be sure to read them all regularly.
Read the manual to see if your question is answered there before posting. Many users will not reply if the answer is already available in the manual.
If your question is about troubleshooting, configuration, or tuning, you MUST include your processor type (MS-I or MS-II) and code version in your post. If your question is about PCB assembly or modifications, you must also include the main board version number (1.01, 2.2 or 3.0).
If you have questions about MS1/Extra or MS2/Extra code configuration or tuning, please post them at www.msextra.com Such questions posted here will be moved to: a temporary MSextra sub-forum, where they will be removed after 7 days
The full forum rules are here: Forum Rules, be sure to read them all regularly.
-
nnffssaa
- MegaSquirt Newbie
- Posts: 9
- Joined: Mon Jun 27, 2011 11:56 pm
- Location: taiwan taipei
- Contact:
can't set basic table
since i update firmware from 2.6 to 2.891(MS II V3.57)
can't set the basic table
what's the problem with that?
and thanks for reply
MS new guy
i use sym RV 180 engine(motorcycle engine 171 c.c) with bosch 0 277 100 124 ignition control
can't set the basic table
what's the problem with that?
and thanks for reply
MS new guy
i use sym RV 180 engine(motorcycle engine 171 c.c) with bosch 0 277 100 124 ignition control
-
Matt Cramer
- Super Squirter
- Posts: 2951
- Joined: Sat Jul 03, 2004 11:35 am
Re: can't set basic table
Is your MSQ set up for using a MAF?
It might help if you posted a whole copy of the MSQ - that would give more info on what settings might be locking you out.
It might help if you posted a whole copy of the MSQ - that would give more info on what settings might be locking you out.
-
nnffssaa
- MegaSquirt Newbie
- Posts: 9
- Joined: Mon Jun 27, 2011 11:56 pm
- Location: taiwan taipei
- Contact:
Re: can't set basic table
thx for your replyMatt Cramer wrote:Is your MSQ set up for using a MAF?
It might help if you posted a whole copy of the MSQ - that would give more info on what settings might be locking you out.
when i saw your suggestion, now i find out the problem.
that i select map only. when i selection adjust map for bar,the spark and ve table is able to use.
and sorry to you ,because i forget to view the 2.8 manual
i just reviewed the older manual
SRY and thanks for your reply
-
nnffssaa
- MegaSquirt Newbie
- Posts: 9
- Joined: Mon Jun 27, 2011 11:56 pm
- Location: taiwan taipei
- Contact:
Re: can't set basic table
but i have some question
when i cranking the engine,the wue always on off .But i set that 100
when i cranking the engine,the wue always on off .But i set that 100
-
nnffssaa
- MegaSquirt Newbie
- Posts: 9
- Joined: Mon Jun 27, 2011 11:56 pm
- Location: taiwan taipei
- Contact:
Re: can't set basic table
this is my MSQ
You do not have the required permissions to view the files attached to this post.
-
Matt Cramer
- Super Squirter
- Posts: 2951
- Joined: Sat Jul 03, 2004 11:35 am
Re: can't set basic table
Well, yes... 100% WUE means the WUE is off.nnffssaa wrote:but i have some question
when i cranking the engine,the wue always on off .But i set that 100
-
nnffssaa
- MegaSquirt Newbie
- Posts: 9
- Joined: Mon Jun 27, 2011 11:56 pm
- Location: taiwan taipei
- Contact:
Re: can't set basic table
but when i cranking engine WUE indicator always flicker,and engine difficult to start.Matt Cramer wrote:Well, yes... 100% WUE means the WUE is off.nnffssaa wrote:but i have some question
when i cranking the engine,the wue always on off .But i set that 100