does someone have pics of their board?

bentvalve · Post by **bentvalve** » Thu Mar 15, 2012 12:42 pm

1st this is ms2 v.3.0 board..

im lost on the pwmiac mod! i know what it says but, i dont want to mess up a board.. i wish there were pinned pics of what the mods should look like. like where can i install the 120 on the heat sink? if someone is at this point please post a pic! the onl mods that will be done (edis,pwmiac,boost control) thanks for any direction...don russell

BreakDancer · Post by **BreakDancer** » Fri Mar 16, 2012 5:06 am

Here you go should be able to find what your looking for.

http://www.google.com/search?tbm=isch&h ... 5l0.frgbld.

bentvalve · Post by **bentvalve** » Fri Mar 16, 2012 6:46 am

wow, that was so helpful! so , i can do a search like that for like the boost control and others? i like pictures. i have ms and i have serious cognitive issues.. i can talk about the stuff all day, but when it gets time to do it ..im lost.. thanks for your help! don russell

BreakDancer · Post by **BreakDancer** » Fri Mar 16, 2012 7:49 am

bentvalve wrote:wow, that was so helpful! so , i can do a search like that for like the boost control and others? i like pictures. i have ms and i have serious cognitive issues.. i can talk about the stuff all day, but when it gets time to do it ..im lost.. thanks for your help! don russell

Bentvalve, I was not being a yank Did you follow the link? I scrolled thru and there are tons of pics showing how to wire the PWM. Unless Im misunderstanding what it is you are looking for? Sorry I was only trying to help, I could give you pics of mine if you want but it looks exactly like the one in the first pic in the link.

BreakDancer · Post by **BreakDancer** » Fri Mar 16, 2012 8:00 am

bentvalve · Post by **bentvalve** » Fri Mar 16, 2012 9:03 am

im sorry, i was not being sarcastic.. i was like wow just what i was looking for!!! and i think u for your time and effort to help me out!!! don russell

trakkies · Post by **trakkies** » Fri Mar 16, 2012 10:09 am

I've not done this mod, but since the IGBT driver has both in and out on pads it might be possible to fit that high current transistor to the PCB where it goes and avoid have that rat's nest.

bentvalve · Post by **bentvalve** » Fri Mar 16, 2012 11:11 am

yes, i would like it to be cleaner..but, once again i would need part#'s and pics if possible. im open to all suggestion! thanks..don russell

BreakDancer · Post by **BreakDancer** » Fri Mar 16, 2012 7:58 pm

+3 on the cleaner install. This was the only way I knew to do it. If there is something nicer I would change it.

trakkies · Post by **trakkies** » Sat Mar 17, 2012 6:33 am

BreakDancer wrote:+3 on the cleaner install. This was the only way I knew to do it. If there is something nicer I would change it.

Waiting in for a delivery which is late so here we go:-

Remove Q4, R43, R57 and IGBT driver, if installed. Mount the TIP 120 where the IGBT driver goes and solder to the IGBT PCB holes. Then wire as per the pic - the wiring can be on the reverse side of the PCB to keep things neat.

bentvalve · Post by **bentvalve** » Sat Mar 17, 2012 8:13 pm

yes, the way breakdancer showed it was the way i would have done it. i thank you breakdancer for the link and pics! but, this is looking pretty sweet and clean! well as long as i do not need the igbt.. which i hope is for maybe gm hei? i will be using ford edis. thanks to trakkies.. don

MSefi.com read only forum (Jan.15,2018)

does someone have pics of their board?

does someone have pics of their board?

Re: does someone have pics of their board?

Re: does someone have pics of their board?

Re: does someone have pics of their board?

Re: does someone have pics of their board?

Re: does someone have pics of their board?

Re: does someone have pics of their board?

Re: does someone have pics of their board?

Re: does someone have pics of their board?

Re: does someone have pics of their board?

Re: does someone have pics of their board?