hello,
I need help i am running a registered version of TS trying to configure an MSII efi v3.57 with code rev. 2.905.
I am trying to open basic tables and every single one is greyed out and unmodifiable. I have reloaded TS a couple times.
i have tried running TSlite on another laptop and have been able to get at the VE, afr, and spark tables.
additionally i cannot locate the VE generator and i am unsure if i have set base settings for the ignition correctly. i am trying to implement ms on a 1989 honda civic with the stock distributor.
any help is greatly appreciated, i am getting super frustrated searching for answers. i have attached my current msq.
Thanks,
Juan
strange problems with TS
Forum rules
Read the manual to see if your question is answered there before posting. Many users will not reply if the answer is already available in the manual.
If your question is about troubleshooting, configuration, or tuning, you MUST include your processor type (MS-I or MS-II) and code version in your post. If your question is about PCB assembly or modifications, you must also include the main board version number (1.01, 2.2 or 3.0). For tuning/troubleshooting questions, please attached a datalog and your MSQ file to your post.
If you have questions about MS1/Extra or MS2/Extra code configuration or tuning, please post them at www.msextra.com Such questions posted here will be moved to: a temporary MSextra sub-forum, where they will be removed after 7 days
The full forum rules are here: Forum Rules, be sure to read them all regularly.
Read the manual to see if your question is answered there before posting. Many users will not reply if the answer is already available in the manual.
If your question is about troubleshooting, configuration, or tuning, you MUST include your processor type (MS-I or MS-II) and code version in your post. If your question is about PCB assembly or modifications, you must also include the main board version number (1.01, 2.2 or 3.0). For tuning/troubleshooting questions, please attached a datalog and your MSQ file to your post.
If you have questions about MS1/Extra or MS2/Extra code configuration or tuning, please post them at www.msextra.com Such questions posted here will be moved to: a temporary MSextra sub-forum, where they will be removed after 7 days
The full forum rules are here: Forum Rules, be sure to read them all regularly.
strange problems with TS
You do not have the required permissions to view the files attached to this post.
-
kjones6039
- Master Squirter
- Posts: 618
- Joined: Sat Jul 22, 2006 7:02 pm
- Location: Eureka, Nevada USA
- Contact:
Re: strange problems with TS
What version of TS are we talking here?
Ken
Ken
1979 Corvette - 383 CID SBC w/ Holley Pro-Jection 900 CFM TBI, 4-85 lb lo-z injectors & Walbro 255 pump
MS2 v3 w/ms2extra 3.4.0 Release
36-1, Delphi LS2/7 coils in wasted spark, driven by v2.0 logic board from JBPerformance
Spartan Lambda Sensor from 14point7
MS2 v3 w/ms2extra 3.4.0 Release
36-1, Delphi LS2/7 coils in wasted spark, driven by v2.0 logic board from JBPerformance
Spartan Lambda Sensor from 14point7
Re: strange problems with TS
I have the latest version of tunerstudio running on a laptop running windows xp tablet edition.
Re: strange problems with TS
TS v1.007
-
LT401Vette
- Master Squirter
- Posts: 481
- Joined: Sat Jul 16, 2005 7:07 am
- Location: Charlotte, NC
- Contact:
Re: strange problems with TS
This is a common problem.
With MSII B&G firmware, there is a Project setting for MAPBaro and a firmware setting for MAP Baro, if 1 is on the other must be too or your tables will be disabled.
Check the setting:
"Fuel Set-Up" --> "Other Fuel Settings" --> "VE/SPK/AFR table index"
and in the Project Properties (Press CTRL+P), click the Settings tab
Check the "MAP Baro" Setting.
You need to make sure they are either both set to MAP Baro, or both not set to MAP Baro.
With MSII B&G firmware, there is a Project setting for MAPBaro and a firmware setting for MAP Baro, if 1 is on the other must be too or your tables will be disabled.
Check the setting:
"Fuel Set-Up" --> "Other Fuel Settings" --> "VE/SPK/AFR table index"
and in the Project Properties (Press CTRL+P), click the Settings tab
Check the "MAP Baro" Setting.
You need to make sure they are either both set to MAP Baro, or both not set to MAP Baro.
Phil Tobin
EFI Analytics, helping to simplify EFI with Next Generation tuning software.
http://www.tunerstudio.com/
http://www.efiAnalytics.com/MegaLogViewer/
Android Shadow Dash MS: http://tunerstudio.com/index.php/shadowdashmsmenu
EFI Analytics, helping to simplify EFI with Next Generation tuning software.
http://www.tunerstudio.com/
http://www.efiAnalytics.com/MegaLogViewer/
Android Shadow Dash MS: http://tunerstudio.com/index.php/shadowdashmsmenu