Wondering which part of the instructions I should follow for this.
http://www.summitracing.com/parts/crn-7 ... /chevrolet
http://www.cranecams.com/402-407.pdf
I'm getting confused when it gets to the jumpers...The IGBT is also starting to confuse me, along with the hi/low circuits...
The rest of my planned setup is GM TBI with whatever GM sensors I need to run, which I thought I needed the MAP sensor from the GM donor but the MS2 v3 came with a MAP? I'm fairly sure I didn't order it with the mapdaddy 4, but this is installed on the bottom of the PCB...Also this is all on a '65 Rambler with a 287cid V8...(if this helps with how I need to set up my MS2)
I did not intend on controlling the ignition with the MS, just picking up a signal from the distributor to run the TBI, tho the instructions seemed to lead me to set it up for ignition control or did I mis-read and re-mis-read? I would use the MS to control the ignition if its possible with the setup I have if it will give me better road manners along with better fuel economy.
I have tested the power supply and all is well, waiting on a 9pin to USB cable and getting my laptop setup with all the software to use with the MS. So bench testing is out for a few days.
MS2 v3 with Crane XR-i?
Forum rules
Read the manual to see if your question is answered there before posting. Many users will not reply if the answer is already available in the manual.
If your question is about troubleshooting, configuration, or tuning, you MUST include your processor type (MS-I or MS-II) and code version in your post. If your question is about PCB assembly or modifications, you must also include the main board version number (1.01, 2.2 or 3.0).
If you have questions about MS1/Extra or MS2/Extra code configuration or tuning, please post them at www.msextra.com Such questions posted here will be moved to: a temporary MSextra sub-forum, where they will be removed after 7 days
The full forum rules are here: Forum Rules, be sure to read them all regularly.
Read the manual to see if your question is answered there before posting. Many users will not reply if the answer is already available in the manual.
If your question is about troubleshooting, configuration, or tuning, you MUST include your processor type (MS-I or MS-II) and code version in your post. If your question is about PCB assembly or modifications, you must also include the main board version number (1.01, 2.2 or 3.0).
If you have questions about MS1/Extra or MS2/Extra code configuration or tuning, please post them at www.msextra.com Such questions posted here will be moved to: a temporary MSextra sub-forum, where they will be removed after 7 days
The full forum rules are here: Forum Rules, be sure to read them all regularly.
-
Matt Cramer
- Super Squirter
- Posts: 2951
- Joined: Sat Jul 03, 2004 11:35 am
Re: MS2 v3 with Crane XR-i?
Set the MS2 up for fuel only and trigger off the coil negative terminal.
The MS2 will have a built in MAP sensor.
The MS2 will have a built in MAP sensor.
Re: MS2 v3 with Crane XR-i?
Awesome! Thank you for the reply, I guess I got some back tracking to do and set it up for neg. trigger...
Also I'm wanting to stay away from the Innovate controller and have looked and searched for many others, I'm leaning towards: http://www.betterpartx.com/bpsx_digital ... re_display I haven't found anything bad, but I have not found many using it. Am I still on the right track to running Wideband or should I look into the more commonly used WBO2 controllers?
Also I'm wanting to stay away from the Innovate controller and have looked and searched for many others, I'm leaning towards: http://www.betterpartx.com/bpsx_digital ... re_display I haven't found anything bad, but I have not found many using it. Am I still on the right track to running Wideband or should I look into the more commonly used WBO2 controllers?