Retrieving Msq. From Megasquirt

For discussing Phil Tobin's TunerStudio MS is the MegaSquirt edition of TunerStudio, a next generation tuning application. It provides the ability to configure and tune all MegaSquirt controllers and is 100% compatible with MegaTune ini files and msq's.

Moderator: LT401Vette

Forum rules
Post Reply
jamesbryan
MegaSquirt Newbie
Posts: 10
Joined: Sat Feb 02, 2013 6:14 pm

Retrieving Msq. From Megasquirt

Post by jamesbryan »

My laptop took a major dump and I lost all my msq. files and datalogs. Is it possible to retrieve my current tune just by hooking up another computer with tuner studio to the controller? It sucks to lose my data logs but I had been getting close to the tune I wanted. And not sure if it will download onto the new computer.

Thanks
Top
kjones6039
Master Squirter
Posts: 618
Joined: Sat Jul 22, 2006 7:02 pm
Location: Eureka, Nevada USA
Contact:
Contact kjones6039

Re: Retrieving Msq. From Megasquirt

Post by kjones6039 »

jamesbryan wrote:My laptop took a major dump and I lost all my msq. files and datalogs. Is it possible to retrieve my current tune just by hooking up another computer with tuner studio to the controller? It sucks to lose my data logs but I had been getting close to the tune I wanted. And not sure if it will download onto the new computer.

Thanks
Yes. Just connect to MS, create a new project and save it

I like to use the TS archive utility to make regular backups of all my project files, and store them somewhere, just for occasions like you describe.

Ken
1979 Corvette - 383 CID SBC w/ Holley Pro-Jection 900 CFM TBI, 4-85 lb lo-z injectors & Walbro 255 pump
MS2 v3 w/ms2extra 3.4.0 Release
36-1, Delphi LS2/7 coils in wasted spark, driven by v2.0 logic board from JBPerformance
Spartan Lambda Sensor from 14point7
Top
jamesbryan
MegaSquirt Newbie
Posts: 10
Joined: Sat Feb 02, 2013 6:14 pm

Re: Retrieving Msq. From Megasquirt

Post by jamesbryan »

OK...Having issues matching firmware. My controller is rev 2.92000 and cant seem to find out how to match to get TS to open when connected.
any quick suggestions. When connected TS will see my MS but I cant figure out how to match firmware.

Thanks
Top
kjones6039
Master Squirter
Posts: 618
Joined: Sat Jul 22, 2006 7:02 pm
Location: Eureka, Nevada USA
Contact:
Contact kjones6039

Re: Retrieving Msq. From Megasquirt

Post by kjones6039 »

You will need to download/install the 2.9 ini in you new project.

Ken
1979 Corvette - 383 CID SBC w/ Holley Pro-Jection 900 CFM TBI, 4-85 lb lo-z injectors & Walbro 255 pump
MS2 v3 w/ms2extra 3.4.0 Release
36-1, Delphi LS2/7 coils in wasted spark, driven by v2.0 logic board from JBPerformance
Spartan Lambda Sensor from 14point7
Top
jamesbryan
MegaSquirt Newbie
Posts: 10
Joined: Sat Feb 02, 2013 6:14 pm

Re: Retrieving Msq. From Megasquirt

Post by jamesbryan »

Thanks. Matt sent me an e mail with the link for the V2.92 ini.

All is good and back to tuning. Thanks again
Top
Post Reply

Return to “TunerStudioMS”