RPM Reading inacuate

This forum is for discussing ignition setup, tuning, and troubleshooting for MS-II. Click these links for info on GM's HEI, EDIS, direct coil control, others.
Forum rules
Read the manual to see if your question is answered there before posting. Many users will not reply if the answer is already available in the manual.

If your question is about troubleshooting, configuration, or tuning, you MUST include your processor type (MS-I or MS-II) and code version in your post. If your question is about PCB assembly or modifications, you must also include the main board version number (1.01, 2.2 or 3.0). For tuning/troubleshooting questions, please attached a datalog and your MSQ file to your post.

If you have questions about MS1/Extra or MS2/Extra code configuration or tuning, please post them at www.msextra.com Such questions posted here will be moved to: a temporary MSextra sub-forum, where they will be removed after 7 days

The full forum rules are here: Forum Rules, be sure to read them all regularly.
Post Reply
skip406
MegaSquirt Newbie
Posts: 11
Joined: Thu Nov 21, 2013 5:18 pm

RPM Reading inacuate

Post by skip406 »

Hi i am using MS-II V-3.0 on a buggy with a suzuki swift gt 1994 1.3 liter dohc supercharged, it started up fine but the RPM is reading two to three
time's what it actually is,any help would be great.
ps im a newby and i cant type.
Top
Matt Cramer
Super Squirter
Posts: 2951
Joined: Sat Jul 03, 2004 11:35 am

Re: RPM Reading inacuate

Post by Matt Cramer »

Can you post a copy of your MSQ?

What exactly are you using for RPM input?
Top
skip406
MegaSquirt Newbie
Posts: 11
Joined: Thu Nov 21, 2013 5:18 pm

Re: RPM Reading inacuate

Post by skip406 »

Sorry about the lack of info. I am running MS-II 3.0 with v 2.92 firmware with suzuki swift dist, direct coil controll, conected as the manual says,coil + to 12volt off fuel pump relay
coil - to ign output #36, using vr in dist wired to pin#2 and #25. And im not sure how to get my msq over to here.
Top
kjones6039
Master Squirter
Posts: 618
Joined: Sat Jul 22, 2006 7:02 pm
Location: Eureka, Nevada USA
Contact:
Contact kjones6039

Re: RPM Reading inacuate

Post by kjones6039 »

skip406 wrote:And im not sure how to get my msq over to here.
In the Reply window, click on the Upload attachment tab and browse for your msq file.

Ken
1979 Corvette - 383 CID SBC w/ Holley Pro-Jection 900 CFM TBI, 4-85 lb lo-z injectors & Walbro 255 pump
MS2 v3 w/ms2extra 3.4.0 Release
36-1, Delphi LS2/7 coils in wasted spark, driven by v2.0 logic board from JBPerformance
Spartan Lambda Sensor from 14point7
Top
skip406
MegaSquirt Newbie
Posts: 11
Joined: Thu Nov 21, 2013 5:18 pm

Re: RPM Reading inacuate

Post by skip406 »

PART_1371696767967.jpeg
I hope this is what is needed, I included a pic of the dist
You do not have the required permissions to view the files attached to this post.
Top
skip406
MegaSquirt Newbie
Posts: 11
Joined: Thu Nov 21, 2013 5:18 pm

Re: RPM Reading inacuate

Post by skip406 »

I hope this msq helps any info would be great thanks mat.
You do not have the required permissions to view the files attached to this post.
Top
Matt Cramer
Super Squirter
Posts: 2951
Joined: Sat Jul 03, 2004 11:35 am

Re: RPM Reading inacuate

Post by Matt Cramer »

MS2 B&G code does not work with that pattern. You will have to either cut the wheel down to four equally spaced teeth, or use MS2/Extra code, which has a separate support forum on MSExtra.com.
Top
skip406
MegaSquirt Newbie
Posts: 11
Joined: Thu Nov 21, 2013 5:18 pm

Re: RPM Reading inacuate

Post by skip406 »

thanks i figured i would have to cut down the reluctor.
Top
skip406
MegaSquirt Newbie
Posts: 11
Joined: Thu Nov 21, 2013 5:18 pm

Re: RPM Reading inacuate

Post by skip406 »

Matt thanks for the info i cut off eight of the reluctor points and it runs great!!
Top
Post Reply

Return to “MS-II Ignition Setup, Tuning, and Troubleshooting”