Just wondering. I've got an old unit I used MegaTune with and thought I'd ask if TS would run it. I have v 3.4.0 installed on a new tuning laptop, pretty decent machine with a native serial port.
I still have the old laptop with MT and my old tuning files which I can use with it but I gave the controller to my brother for his TR7/1UZ conversion. He has a laptop he uses with his other, newer controller in his TR4 on which he uses TS. I know he'd rather stick with that software if he can.
Jim
TS compatible with MS2 v1.0?
Moderator: LT401Vette
-
Jim Blackwood
- MegaSquirt Newbie
- Posts: 15
- Joined: Thu Jul 29, 2004 5:31 pm
- Location: Gunpowder Rd
-
LT401Vette
- Master Squirter
- Posts: 481
- Joined: Sat Jul 16, 2005 7:07 am
- Location: Charlotte, NC
- Contact:
Re: TS compatible with MS2 v1.0?
It should, but I can't say I've tested against something that old in years 
.
TunerStudio does not have the ini for that though, so you will need to get the ini file from the laptop that has MegaTune on it.
There is no TunerStudio 3.4, so that must be a firmware version.
.TunerStudio does not have the ini for that though, so you will need to get the ini file from the laptop that has MegaTune on it.
There is no TunerStudio 3.4, so that must be a firmware version.
Phil Tobin
EFI Analytics, helping to simplify EFI with Next Generation tuning software.
http://www.tunerstudio.com/
http://www.efiAnalytics.com/MegaLogViewer/
Android Shadow Dash MS: http://tunerstudio.com/index.php/shadowdashmsmenu
EFI Analytics, helping to simplify EFI with Next Generation tuning software.
http://www.tunerstudio.com/
http://www.efiAnalytics.com/MegaLogViewer/
Android Shadow Dash MS: http://tunerstudio.com/index.php/shadowdashmsmenu
-
Jim Blackwood
- MegaSquirt Newbie
- Posts: 15
- Joined: Thu Jul 29, 2004 5:31 pm
- Location: Gunpowder Rd
Re: TS compatible with MS2 v1.0?
Danged old memory error strikes again! Sorry Phil, 2.6.19, what was I thinking?
I have an .ini file on the desktop of the old Stinkpad, does 2.3 sound about right? I think that's probably it.
I have to reload the s19 file too since the aborted attempt at upgrading the firmware erased it. I didn't realize it was the v. 1.0 MS2 card. (Thought that one was in the spares box with the old 68HC908) So I'll have to do a little research to sort out which s19 file to use. There is a v1.31 and a v2.32 on the desktop, so I'd guess one or the other should work, probably the 1.31. Also have MS Download 2.0 on there. It's been a long time since I used those but I did it before, surely I can do it again.
Once I've reloaded the firmware I'll see if I can run TS with it. Hopefully tomorrow. (fingers crossed)
I kept the controller when I got rid of the old I-H Travelall, had it just sitting around. Dan needed something for his engine swap so I just figured, why not? It was a good controller back then, should still work now. Neither one of us are Developers so a basic controller is all he needs.
Jim
I have an .ini file on the desktop of the old Stinkpad, does 2.3 sound about right? I think that's probably it.
I have to reload the s19 file too since the aborted attempt at upgrading the firmware erased it. I didn't realize it was the v. 1.0 MS2 card. (Thought that one was in the spares box with the old 68HC908) So I'll have to do a little research to sort out which s19 file to use. There is a v1.31 and a v2.32 on the desktop, so I'd guess one or the other should work, probably the 1.31. Also have MS Download 2.0 on there. It's been a long time since I used those but I did it before, surely I can do it again.
Once I've reloaded the firmware I'll see if I can run TS with it. Hopefully tomorrow. (fingers crossed)
I kept the controller when I got rid of the old I-H Travelall, had it just sitting around. Dan needed something for his engine swap so I just figured, why not? It was a good controller back then, should still work now. Neither one of us are Developers so a basic controller is all he needs.
Jim