Hi ther megatuners. I am new to this forum and struggles a little with my first megasquirt project. The car is a Peugeot 306 with a 1.9L 8v (xu9JA) and megasquirt 1 with PCB 2.2
The problem i have is that the ECU don't connect to the Megatune 2.25 Does any one know if its the ECU or the softwear that is the problem
The ECU Injectors and Warm up LEDs blinks when the key is turned on. Is this right?
new here with a peugeot 306
Forum rules
Read the manual to see if your question is answered there before posting. Many users will not reply if the answer is already available in the manual.
If your question is about troubleshooting, configuration, or tuning, you MUST include your processor type (MS-I or MS-II) and code version in your post. If your question is about PCB assembly or modifications, you must also include the main board version number (1.01, 2.2 or 3.0).
If you have questions about MS1/Extra or MS2/Extra code configuration or tuning, please post them at www.msextra.com Such questions posted here will be moved to: a temporary MSextra sub-forum, where they will be removed after 7 days
The full forum rules are here: Forum Rules, be sure to read them all regularly.
Read the manual to see if your question is answered there before posting. Many users will not reply if the answer is already available in the manual.
If your question is about troubleshooting, configuration, or tuning, you MUST include your processor type (MS-I or MS-II) and code version in your post. If your question is about PCB assembly or modifications, you must also include the main board version number (1.01, 2.2 or 3.0).
If you have questions about MS1/Extra or MS2/Extra code configuration or tuning, please post them at www.msextra.com Such questions posted here will be moved to: a temporary MSextra sub-forum, where they will be removed after 7 days
The full forum rules are here: Forum Rules, be sure to read them all regularly.
-
kjones6039
- Master Squirter
- Posts: 618
- Joined: Sat Jul 22, 2006 7:02 pm
- Location: Eureka, Nevada USA
- Contact:
Re: new here with a peugeot 306
Do you have a Stim?
If not, this is another strong case for all MegaSquirters to have one. Perhaps you could borrow one?
From there I would suggest making certain you are using the correct serial port.
Ken
If not, this is another strong case for all MegaSquirters to have one. Perhaps you could borrow one?
From there I would suggest making certain you are using the correct serial port.
Ken
1979 Corvette - 383 CID SBC w/ Holley Pro-Jection 900 CFM TBI, 4-85 lb lo-z injectors & Walbro 255 pump
MS2 v3 w/ms2extra 3.4.0 Release
36-1, Delphi LS2/7 coils in wasted spark, driven by v2.0 logic board from JBPerformance
Spartan Lambda Sensor from 14point7
MS2 v3 w/ms2extra 3.4.0 Release
36-1, Delphi LS2/7 coils in wasted spark, driven by v2.0 logic board from JBPerformance
Spartan Lambda Sensor from 14point7
-
Bernard Fife
- Master Squirter
- Posts: 475
- Joined: Thu Oct 29, 2009 12:54 pm
Re: new here with a peugeot 306
"Never wrestle with pigs. You both get dirty and the pig likes it.” - George Bernard Shaw
Re: new here with a peugeot 306
I just ordered a stim from DIYAutoTune, but havent recived it yet. looking forward to recieve it. hope this helps me.kjones6039 wrote:Do you have a Stim?
If not, this is another strong case for all MegaSquirters to have one. Perhaps you could borrow one?
From there I would suggest making certain you are using the correct serial port.
Ken