here http://www.DIYAutoTune.com/tech_article ... _board.htm it says dwell should be around 2.0ms.
Question is, should i set to 2.0ms in MT and it shows on gauge 1.7ms or should i set to 2.3ms so that gauge will show 2.0ms
Best regards
Dwell setting question
Forum rules
Read the manual to see if your question is answered there before posting. Many users will not reply if the answer is already available in the manual.
If your question is about troubleshooting, configuration, or tuning, you MUST include your processor type (MS-I or MS-II) and code version in your post. If your question is about PCB assembly or modifications, you must also include the main board version number (1.01, 2.2 or 3.0). For tuning/troubleshooting questions, please attached a datalog and your MSQ file to your post.
If you have questions about MS1/Extra or MS2/Extra code configuration or tuning, please post them at www.msextra.com Such questions posted here will be moved to: a temporary MSextra sub-forum, where they will be removed after 7 days
The full forum rules are here: Forum Rules, be sure to read them all regularly.
Read the manual to see if your question is answered there before posting. Many users will not reply if the answer is already available in the manual.
If your question is about troubleshooting, configuration, or tuning, you MUST include your processor type (MS-I or MS-II) and code version in your post. If your question is about PCB assembly or modifications, you must also include the main board version number (1.01, 2.2 or 3.0). For tuning/troubleshooting questions, please attached a datalog and your MSQ file to your post.
If you have questions about MS1/Extra or MS2/Extra code configuration or tuning, please post them at www.msextra.com Such questions posted here will be moved to: a temporary MSextra sub-forum, where they will be removed after 7 days
The full forum rules are here: Forum Rules, be sure to read them all regularly.
Dwell setting question
MS2 PBC 3.0 B&G 2.98
here http://www.DIYAutoTune.com/tech_article ... _board.htm it says dwell should be around 2.0ms.
Question is, should i set to 2.0ms in MT and it shows on gauge 1.7ms or should i set to 2.3ms so that gauge will show 2.0ms
Best regards
here http://www.DIYAutoTune.com/tech_article ... _board.htm it says dwell should be around 2.0ms.
Question is, should i set to 2.0ms in MT and it shows on gauge 1.7ms or should i set to 2.3ms so that gauge will show 2.0ms
Best regards
Pontiac Firebird 305 LT1 intake, L82 cam
MegaSquirt II with mod's + TPI adaptor board, MSExtra 3.3
MegaSquirt II with mod's + TPI adaptor board, MSExtra 3.3
-
Bernard Fife
- Master Squirter
- Posts: 475
- Joined: Thu Oct 29, 2009 12:54 pm
Re: Dwell setting question
WASyL,
Typically this means to set the dwell parameter Maximum Dwell Duration (ms) to 2.0 milliseconds. The actual dwell will then be lowered a bit by the voltage compensation, and this is totally fine. There is more on setting dwell here: http://www.megamanual.com/ms2/configure.htm#dwell
Lance.
Typically this means to set the dwell parameter Maximum Dwell Duration (ms) to 2.0 milliseconds. The actual dwell will then be lowered a bit by the voltage compensation, and this is totally fine. There is more on setting dwell here: http://www.megamanual.com/ms2/configure.htm#dwell
Lance.
"Never wrestle with pigs. You both get dirty and the pig likes it.” - George Bernard Shaw
Re: Dwell setting question
thanks Lance
i have memorised whole megamanual for MSII code B&G 2.8 but i wanted to make sure by asking additional question to confirm what i have understanded as english is not my native language
best regards
i have memorised whole megamanual for MSII code B&G 2.8 but i wanted to make sure by asking additional question to confirm what i have understanded as english is not my native language
best regards
Pontiac Firebird 305 LT1 intake, L82 cam
MegaSquirt II with mod's + TPI adaptor board, MSExtra 3.3
MegaSquirt II with mod's + TPI adaptor board, MSExtra 3.3