and tested with several different edis-4 engines, engine capacity and all with the same result, something very strange is that all modules have the same numbering.
What can happen?, All on the same revs and different engines is very strange.
at home with the stimulator works well, I have the limit at 8000rpm with fuel cut when it gets to 8000rpm and the pulse is 0.
signal loses rpm 6750rpm
Forum rules
Read the manual to see if your question is answered there before posting. Many users will not reply if the answer is already available in the manual.
If your question is about troubleshooting, configuration, or tuning, you MUST include your processor type (MS-I or MS-II) and code version in your post. If your question is about PCB assembly or modifications, you must also include the main board version number (1.01, 2.2 or 3.0). For tuning/troubleshooting questions, please attached a datalog and your MSQ file to your post.
If you have questions about MS1/Extra or MS2/Extra code configuration or tuning, please post them at www.msextra.com Such questions posted here will be moved to: a temporary MSextra sub-forum, where they will be removed after 7 days
The full forum rules are here: Forum Rules, be sure to read them all regularly.
Read the manual to see if your question is answered there before posting. Many users will not reply if the answer is already available in the manual.
If your question is about troubleshooting, configuration, or tuning, you MUST include your processor type (MS-I or MS-II) and code version in your post. If your question is about PCB assembly or modifications, you must also include the main board version number (1.01, 2.2 or 3.0). For tuning/troubleshooting questions, please attached a datalog and your MSQ file to your post.
If you have questions about MS1/Extra or MS2/Extra code configuration or tuning, please post them at www.msextra.com Such questions posted here will be moved to: a temporary MSextra sub-forum, where they will be removed after 7 days
The full forum rules are here: Forum Rules, be sure to read them all regularly.
-
valenciano
- Helpful Squirter
- Posts: 43
- Joined: Fri Sep 05, 2008 12:44 pm
-
Matt Cramer
- Super Squirter
- Posts: 2951
- Joined: Sat Jul 03, 2004 11:35 am
Re: signal loses rpm 6750rpm
You don't have an oscilloscope by any chance, do you?
-
valenciano
- Helpful Squirter
- Posts: 43
- Joined: Fri Sep 05, 2008 12:44 pm
Re: signal loses rpm 6750rpm
I have no oscilloscope Matt, I'm trying to buy a digital one economical, but so far I have not
What do you see?
the truth is that I'm thinking about making on without edis-4, direct ms2 and coils 36-1 over the wheel, so read is not much work and can be a solution, although I have some doubts, know whether to ms2 to microsquirt to one given problem
What do you see?
the truth is that I'm thinking about making on without edis-4, direct ms2 and coils 36-1 over the wheel, so read is not much work and can be a solution, although I have some doubts, know whether to ms2 to microsquirt to one given problem
-
valenciano
- Helpful Squirter
- Posts: 43
- Joined: Fri Sep 05, 2008 12:44 pm
Re: signal loses rpm 6750rpm
one last thing, configuraon reading your content, it says to ger off-set = 0, I have 2.5 can cause this problem?, I do that for the stimulator works well but not so sure.
-
Matt Cramer
- Super Squirter
- Posts: 2951
- Joined: Sat Jul 03, 2004 11:35 am
Re: signal loses rpm 6750rpm
It sounds like the module has a built in 6750 RPM rev limit. Offset can be used to compensate for a slightly "off" trigger wheel and should not be the cause of the problem. The offset merely shifts the timing by the number of degrees entered.
-
valenciano
- Helpful Squirter
- Posts: 43
- Joined: Fri Sep 05, 2008 12:44 pm
Re: signal loses rpm 6750rpm
ok Matt, I will make direct contact with the wheel rolls 36-1, habrire a new topic in assembly, thanks for the help.