I have a MS-II v3.0 running 2.92 code. It is on a gen-1 small block Chevy, I have a FAST TBI unit sitting on the intake, 14point7 O2 controller, and am running Ford EDIS ignition.
I have just recently switched to EDIS to work around a timing issue I was fighting, and the 14point7 is also new at the same time to replace a defective LC-1. Now that I am confident in those two things, I am working on getting my VE table tuned in. Using Tuner Studio's "Tune Analyze Live" feature works REALLY great the best I can tell. I am not 100% confident that I have the optimal settings, but it sure seems to be doing a good job. However, I wish there was another way besides carrying a laptop with me everywhere I go.
I tried the AMC feature of MS today for the first time, letting it tune on the drive to work, and on the way home. But when I got home and plugged into the laptop, AMC had only changed 2 cells of my VE table. Tuner Studio works MUCH faster than that. I was wondering if there are certain AMC settings I should try to move the process along a little faster? Here's what I have now:
Automatic Mixture Control: FLASH Update
Step Size(%): 50
Minimum VE Change: 2
Vertex Tolerance(RPM): 250
Vertex Tolerance(kPa): 6
Table Change Interval(sec): 5
FLASH Update Interval(sec): 180
Update After(events): 2
I also attached the msq so you guys can take a look at that.
I also have an Android phone, and I have seen a little bit here and there about TS for Android, should/could I maybe get setup to run TS off my phone and let TS tune my VE that way? I figure I could take it to a tuner with a dyno, but I figured I might get a little more for my money if I let auto tune work it's magic a little more first?
Thanks!
AMC or TS Tune Analyze Live?
Forum rules
Read the manual to see if your question is answered there before posting. Many users will not reply if the answer is already available in the manual.
If your question is about troubleshooting, configuration, or tuning, you MUST include your processor type (MS-I or MS-II) and code version in your post. If your question is about PCB assembly or modifications, you must also include the main board version number (1.01, 2.2 or 3.0). For tuning/troubleshooting questions, please attached a datalog and your MSQ file to your post.
If you have questions about MS1/Extra or MS2/Extra code configuration or tuning, please post them at www.msextra.com Such questions posted here will be moved to: a temporary MSextra sub-forum, where they will be removed after 7 days
The full forum rules are here: Forum Rules, be sure to read them all regularly.
Read the manual to see if your question is answered there before posting. Many users will not reply if the answer is already available in the manual.
If your question is about troubleshooting, configuration, or tuning, you MUST include your processor type (MS-I or MS-II) and code version in your post. If your question is about PCB assembly or modifications, you must also include the main board version number (1.01, 2.2 or 3.0). For tuning/troubleshooting questions, please attached a datalog and your MSQ file to your post.
If you have questions about MS1/Extra or MS2/Extra code configuration or tuning, please post them at www.msextra.com Such questions posted here will be moved to: a temporary MSextra sub-forum, where they will be removed after 7 days
The full forum rules are here: Forum Rules, be sure to read them all regularly.
AMC or TS Tune Analyze Live?
You do not have the required permissions to view the files attached to this post.
Re: AMC or TS Tune Analyze Live?
Just wondering if anyone ever replied to this as I am kind of wondering the same thing. I've read over, over, over and over the Automatic Mixture control page and at least for me the descriptions of what each setting does seems a little to vague for me to understand just exactly what each setting will do.